Philips FW545, Manual

Page: 11 / 26

11
English
3139 116 18533
To start the demonstration mode
• Press and hold STOP•CLEAR
Ç
(on
the system only) for 5 seconds when
the system is in standby mode.
™ The demonstration will begin.
Easy Set
EASY SET allows you to store all available
radio stations and RDS stations
automatically.
1 Press and hold STANDBY ON (on the
system only) for 5 seconds ; when the
system is in standby or demonstration
mode.
™ “ EASY SET ” will be displayed,
and followed by “ TUNER ” and then
“ AUTO ”.
™ EASY SET will start searching for all
radio stations with RDS and then
followed by radio stations on FM,
MW and LW band respectively.
™ All available RDS and radio stations
with sufficient signal strength will be
stored. Up to 40 presets may be
stored.
2 The system will proceed to set the RDS
time automatically with the stored RDS
preset station.
• If no RDS station is available in the first
preset station, the program will exit
automatically.
™ After a radio station is found,
“
EASY SET ” will be displayed
and followed by “ TIME ”
OPERATING THE SYSTEM
• When searching RDS time;
™ “ SEARCH RDS TIME ” will be
displayed.
™ When RDS time is read, “ RDS
TIME ” will be displayed. The
current time will be displayed for 2
seconds and stored automatically.
Notes:
– EASY SET will start with the RDS
station, if there are still presets
available, it will continue to store the
FM, MW and LW bands respectively.
– When EASY SET is used, all previously
stored radio stations will be replaced.
– The last preset radio station or the first
available RDS station will appear on the
display when EASY SET is completed.
– If RDS station does not transmit RDS
time within 90 seconds, the program
will exit automatically and the display
will show “
NO RDS TIME ”.
Switching the system ON
• Press CD , TUNER , TAPE or AUX .
You can also switch on the system by
pressing any one of the CD DIRECT PLAY
buttons.
Switching the system to
standby mode
• Press STANDBY ON again or
B
on the
remote control.
™ The system will switch to standby
mode.
™ (for FW555C only)
About 5 seconds later, the system
will go into an energy saving mode
( < 2 watts ). The low power
STANDBY ON LED will be lit.
Selecting the Source
• Press the respective source selection
button: CD , TUNER , TAPE or AUX .
™ The display indicates the selected
source.
Note:
– For an external source, make sure you
have connected the audio left and right
OUT terminals of the external
equipment (TV, VCR, Laser Disc player,
DVD player or CD Recorder) to the
AUX/CDR IN terminals.
Selecting the Equalizer
Display
You can select the desired equalizer display
for the system. You must not press the DSC
or INCREDIBLE SURROUND button on the
system before using the JOG.
• Rotate the JOG to select the desired
Equalizer Display, NORMAL, TOP
DOWN, or NITE MODE.
™ The selected display will be shown.
NORMAL Display
FRONT
FM
STEREO
BACK
HSD
REPEAT REC
LW MW AM T.A. NEWS
TIMER
60Hz 500Hz 250Hz
1KHz
2KHz 4KHz 8KHz
SHUFFLE PROGRAM
TOP DOWN Display
FRONT
FM
STEREO
BACK
HSD
REPEAT REC
LW MW AM T.A. NEWS
TIMER
60Hz 500Hz 250Hz 1KHz 2KHz 4KHz 8KHz
SHUFFLE PROGRAM
NITE MODE Display
60Hz 500Hz 250Hz
1KHz
2KHz 4KHz 8KHz
FRONT
FM
STEREO
BACK
HSD
REPEAT REC
LW MW AM T.A. NEWS
TIMER
SHUFFLE PROGRAM
Note:
– In NITE MODE, all lights will be
switched off and the display brightness
will be dimmed.
Untitled-13 6/15/00, 1:15 PM 11
Downloaded From Disc-Player.com Philips Manuals