background image

22

23

Types of alarms and alarm modes

Triggering:

 

After waking up, the system will 

run an automatic examination on the battery 

voltage. If the voltage is too low, the lock give 

an alarm and a voice prompt of “Low battery. 

Please replace all batteries”. 

Alarm mode:

 

A voice prompt of “Low battery. 

Please replace all batteries” during unlocking.

Turning off:

 The alarm will be automatically 

turned off.

Triggering:

 The lock is opened by a key

Alarm mode:

 Continuous repeated alarms

Turning off:

 The alarm will be automatically 

turned off or after a successful verification.

8  Troubleshooting

Mechanical key opening alarm

Low battery alarm, prompting you to replace the batteries in time

Anti-dismantle alarm

Triggering:

 The door is pried open and there 

is no fit in the door. 

Alarm mode:

 Continuous repeated alarms.

Turning off:

 Auto-close, or close after a 

successful key verification, or close after the 

normal indoor unlock.

How to use an emergency power

How to replace batteries

When the battery voltage is insufficient, 

and the door cannot be power up from 

the outside, you can power the lock 

through the Micro USB interface by using 

a 5V power bank as an emergency power 

supply. After opening the door lock, 

please replace the batteries immediately.

In case of a system crash and it's 

impossible to open the door from outside, 

please press the Reset button and then 

release to let it reboot automatically. 

The lock is powered by four 1.5V alkaline 

batteries. There are two sets of working 

power inside the battery cabinet. Eight 

batteries can be put in to extend the 

battery life and reduce battery replacement 

frequency. The battery cabinet is located at 

the upper end of the inside escutcheon. By 

pushing the cover upwards, you can remove 

it and then replace  the batteries.

 

Emergency 

power interface 

Reset 

button

Summary of Contents for DDL172LKCC0/97















Reviews: