Philio PSR07 Manual Download Page 5

 
 

Disposal

 

 

 

This marking indicates that this product should not be 
disposed with other household wastes throughout the 

EU. To prevent possible harm to the environment or 
human health from uncontrolled waste disposal, 

recycle it responsibly to promote the sustainable reuse 
of material resources. To return your used device, 

please use the return and collection systems or 

contact the retailer where the product was purchased. 
They can take this product for environmental safe 

recycling.

 

Company of License Holder

Philio Technology Corporation 

Address of License Holder

8F.,No.653-2,Zhongzheng Rd., Xinzhuang 

Dist., New Taipei City 24257,Taiwan(R.O.C) 
 

FCC Interference Statement

 

This equipment has been tested and found to comply with the limits 

for a Class B digital device, pursuant to Part 15 of the FCC Rules.  

These  limits  are  designed  to  provide  reasonable  protection  against 
harmful interference in a residential installation.  

This  equipment  generates,  uses  and  can  radiate  radio  frequency 
energy  and,  if  not  installed  and  used  in  accordance  with  the 

instructions, may cause harmful interference to 
radio communications.  

However, there is no guarantee that interference will not occur in a 

particular installation.  
If  this  equipment  does  cause  harmful  interference  to  radio  or 

television reception, which 
can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one of the following 

measures: 
• Reorient or relocate the receiving antenna. 

• Increase the separation between the equipment and receiver. 

•  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from 
that to which the receiver is connected. 

• Consult the dealer or an experienced radio/TV technician for help. 

This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is 
subject 

to the following two conditions: 
(1) This device may not cause harmful interference, and 

(2)  This  device  must  accept  any  interference  received,  including 
interference that may cause undesired operation. 

FCC  Caution:  Any  changes  or  modifications  not  expressly  approved 

by  the  party  responsible  for  compliance  could  void  the  user's 
authority to operate this equipment. 

This transmitter must not be co-located or operating in conjunction 
with any other antenna or transmitter.

 

Summary of Contents for PSR07






Reviews: