background image

NO.

Name

Def. Valid

Description

Open → Not trigger.

0

Bit5

: Reserve.

0

Bit6

: Reserve.

0

Bit7

: Reserve.

4 Basic ON 

Level

0xFF

All

Setting the BASIC command value.

When the flood trigger on(0xFF), 

send the BASIC CC to the group 2.

5 Auto Report 

Flood State

6

All

The interval time for auto report the

flood state.

Z-Wave Supported Command Class

Command Class

Version

Required Security Class

Z-Wave Plus™ Info

2

None

Security

1

None

Security 2

1

None

Supervision

1

None

Transport Service

2

None

Association

2

Highest granted Security Class

Association Group 
Information

3

Highest granted Security Class

Device Reset Locally

1

Highest granted Security Class

Firmware Update Meta 
Data

5

Highest granted Security Class

Indicator

3

Highest granted Security Class

Manufacturer Specific

2

Highest granted Security Class

Multi-Channel Association

3

Highest granted Security Class

Powerlevel

1

Highest granted Security Class

Version

3

Highest granted Security Class

Configuration

4

Highest granted Security Class

Notification

8

Highest granted Security Class

Battery

1

Highest granted Security Class

Disposal

 

This marking indicates that this product should not be 
disposed with other household wastes throughout the EU. 
To prevent possible harm to the environment or human 
health from uncontrolled waste disposal, recycle it 
responsibly to promote the sustainable reuse of material 
resources. To return your used device, please use the 
return and collection systems or contact the retailer where 
the product was purchased. They can take this product for 
environmental safe recycling.

Philio Technology Corporation
8F.,   No.653-2,   Zhongzheng   Rd.,   Xinzhuang   Dist.,   New   Taipei   City
24257, Taiwan(R.O.C)

www.philio-tech.com

7

Summary of Contents for PAT15









Reviews: