background image

                                                       
FCC Interference Statement 

This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits   are   designed   to   provide   reasonable   protection   against   harmful
interference   in   a   residential   installation.   This   equipment   generates,
uses and can radiate radio frequency energy and, if not installed and
used   in   accordance   with   the   instructions,     may   cause   harmful
interference   to   radio   communications.         However,     there   is   no
guarantee that interference will not occur in a particular installation.  If
this equipment does cause harmful interference to radio or television
reception,   which can be determined by turning the equipment off and
on,  the user is encouraged to try to correct the interference by one of
the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

Consult   the   dealer   or   an   experienced   radio/TV   technician   for
help.

This   device   complies   with   Part   15   of   the   FCC   Rules.   Operation   is
subject to the following two conditions: 
(1) This device may not cause harmful interference, and
(2)   This   device   must   accept   any   interference   received,   including
interference that may cause undesired operation. 
 
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment. 
 
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.

Warning

Do not dispose of electrical appliances as unsorted municipal waste,
use   separate   collection   facilities.   Contact   your   local   government   for
information   regarding   the   collection   systems   available.   If   electrical
appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging
your health and well-being.

When   replacing   old   appliances   with   new   once,   the   retailer   is   legally
obligated to take back your old appliance for disposal at least for free of
charge.

7

Summary of Contents for PAT14








Reviews: