background image

Meter   Get   Command:  

[Command   Class   Meter,   Meter   Get,   Scale

=0x02(W)]

Meter Report Command:

[Command Class Meter

Meter Report

Rate Type = 0x01

Meter

Type = 

0x01

Precision = 1

Scale = 0x02

Size = 4

Meter Value(W) ]

 Example:

Meter Value 1 = 0x00 (W)

Meter Value 2 = 0x00 (W)

Meter Value 3 = 0x03 (W)

Meter Value 4 = 0xEA (W)

Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W

2-2-2 Accumulated Power Consumption (KWh)

When receiving Meter Get Command, it will report Meter Report Command to

the node.

Meter Get Command: 

[Command Class Meter, Meter Get, Scale = 0x00 KWh)]

Meter Report Command:

[Command Class Meter

Meter Report

Rate Type = 0x01

 

Meter

Type = 0x01

 Precision = 2

Scale = 0x00

Size = 4

Meter Value (KWh)]

     Example:

     Scale = 0x00 (KWh)

     Precision = 2

     Size = 4 Bytes (KWh)

     Meter Value 1 = 0x00(KWh)

     Meter Value 2 = 0x01(KWh)

     Meter Value 3 = 0x38(KWh)

     Meter Value 4 = 0xA3(KWh)

     Accumulated power consumption (KWh) = (Meter Value 2*65536) + (Meter

Value 3*256) + (Meter Value 4) = 800.35 (KWh)

2-2-3 Clearing accumulated power consumption

   Whenever re-start counting the accumulated power consumption is needed, you

can use Meter Reset Command to clear it.

Meter Reset Command: 

[Command Class Meter, Meter Reset]

2-2-4 AC load Voltage (V)

    When receiving Meter Get Command, it will report Meter Report Command to

the node.

Meter   Get   Command:

  [Command   Class   Meter,   Meter   Get,   Scale

=0x04(V)]

Meter Report Command:

[Command Class Meter

Meter Report

Rate Type = 0x01

Meter

Type   =   0x01

Precision   =   1

Scale   =   0x04

Size   =   2

 

Meter

Value(V)]

 Example:

Scale = 0x04 (V)

Precision = 1 

Size = 2 (2 Bytes of V)

Meter Value 1 = 0x09(V)

Meter Value 2 = 0x01(V)

AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)

2-2-5 AC load current ( I )

    When receiving Meter Get Command, it will report Meter Report Command to

the node.

Meter Get Command:

 

[Command Class Meter, Meter Get, Scale =0x05(I)]

Meter Report Command:

Summary of Contents for PAN38











Reviews: