background image

 

Choosing a Suitable Location 
 

1.  Do not locate the Switch facing direct sunlight, humid or dusty place. 

2.  The suitable ambient temperature for the Switch is 0°C~40°C. 

3.  Do not locate the Switch where exists combustible substances or any source of 

heat, e.g. fires, radiators, boiler etc. 

4. 

After putting it into use, the body of Switch will become a little bit hot of which 

phenomenon is normal.

 

 
Installation

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

1.  Put  the  in  wall  switch  into  a  wall  box  and  connect  the  AC  power  wire  L,  N  to 

PAN05 connector L, N. 

2.  Connect the wall switch to the PAN05 as Fig1. 
3.  There are 3 mode PAN05 can be configured to match different kind of wall switch, 

please  refer  to  3-1  Edge  /  Pulse  /  Edge-Toggle  mode  which  described  in  next 
section of this user manual.   

4.  If Edge-Toggle mode has been set, and the S1 S2 is connect to normal bi-stable 

switch,  every  time  when  change  the  state  of  the  wall  switch  will  also  swap  the 
state of Relay1. 

 

Programming 
 

1.    Basic Command Class / Binary Switch Command Class 

The  Switch  will  respond  to  BASIC  and  BINARY  commands  that  are  part  of  the 
Z-Wave system. 

 

1-1 BASIC_GET / BINARY_SWITCH_GET 
 

Basic Get Command: [Command Class Basic, Basic Get]

 

Basic Report Command: 
Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)] 
Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]

 

 

Binary  Switch  Get  Command:[Command  Class  Switch  Binary,  Switch 
Binary Get]

 

Binary Switch Report Command: 
Report OFF:[Command Class Switch Binary, Switch Binary Report, Value 
=0(0x00)]
 
Report ON:[Command Class Switch Binary, Switch Binary Report, Value = 
255(0xFF)]

 

 

1-2 BASIC_SET / SWITCH_BINARY_SET 

 

 

 

 

 

 

   

[Command  Class  Basic,  Basic  Set,  Value  =  1~99,  255(0xFF)]:  the  load 
attached to the Switch turns on.

 

[Command  Class  Basic,  Basic  Set,  Value  =  0(0x00)]:  the  load  attached  to 
the Switch turns off.

 

[Command  Class  Switch  Binary,  Switch  Binary  Set,  Value  =  1~99, 
255(0xFF)]
: the load attached to the Switch turns on.

 

[Command  Class  Switch  Binary,  Switch  Binary  Set,  Value  =  0(0x00)]:  the 
load attached to the Switch turns off.

 

 

1.  Z-Wave’s Groups (Association Command Class Version 2) 
 
The Switch can be set to send reports to associated Z-Wave devices. It supports only 
one association group and the group has one node support. Group1 support 
SWITCH_BINARY_REPORT. 
 
For group 1, the Switch will report ON/OFF status of Relay to controller. 
 

Summary of Contents for PAN05-1A







Reviews: