background image

Transport Service

2

None

Battery

1

Highest granted Security Class

Sensor multilevel

11

Highest granted Security Class

Wake up

2

Highest granted Security Class

Specifications

Operating Voltage

CR123A DC3V  (Li-Battery)

Range

Minimum 40M in door and 100M in outdoor,

line of sight

Operating Temperature -10°C ~ 40°C (85% humidity)

Storage Temperature

-20 C ~ 60°C

Location 

Indoor use only

Frequency Range

868.40MHz; 869.85MHz (EU)

908.40MHz; 916.00MHz (USA/Canada)

916MHz (Israel)(PST07-IL)

920~927 MHz(JP/TW),

921.40 MHz, 919.80 MHz(ANZ),

869.00 MHz(RU),

865.20 MHz(IN)

RF Maximum Power 

(peak)

+5dBm (peak) For EU RED directive 

RF Maximum Power 

(Average)

-10dBm (Average) For EU RED directive 

FCC ID

RHHPST07

Specifications   subject   to   change   without   notice   due   to   continuing
product improvement.

                                                          

                                                         

Disposal

This marking indicates that this product should not be 
disposed with other household wastes throughout the EU. 
To prevent possible harm to the environment or human 
health from uncontrolled waste disposal, recycle it 
responsibly to promote the sustainable reuse of material 
resources. To return your used device, please use the 
return and collection systems or contact the retailer where 
the product was purchased. They can take this product for 
environmental safe recycling.

Philio Technology Corporation
8F.,   No.653-2,   Zhongzheng   Rd.,   Xinzhuang   Dist.,   New   Taipei   City
24257, Taiwan(R.O.C)

www.philio-tech.com

FCC interference Statement

This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits   are   designed   to   provide   reasonable   protection   against   harmful
interference   in   a   residential   installation.   This   equipment   generates,
uses and can radiate radio frequency energy and, if not installed and
used   in   accordance   with   the   instructions,   may   cause   harmful
interference to radio communications.   However, there is no guarantee
that   interference   will   not   occur   in   a   particular   installation.     If   this
equipment   does   cause   harmful   interference   to   radio   or   television
reception, which can be determined by turning the equipment off and
on,  the user is encouraged to try to correct the interference by one of

10

Summary of Contents for PST07












Reviews: