Copyright © 2020, Fast ČR, a. s.
Revision 12/2021
EN - 12
Detergent usage
Only use detergents specifically designed for
domestic dishwashers. Keep your detergents in cool,
dry places out of reach of children.
Add the proper detergent for the selected program
to ensure the best performance. The amount of
detergent needed depends on the cycle, load size,
and soil level of dishes.
Do not fill detergent into the detergent
compartment more than required; otherwise you
can see whitish streaks or bluish layers on glass and
dishes and may cause glass corrosion. Continued use
of too much detergent may cause machine damage.
Using little detergent can result in poor cleaning and
you can see whitish streaksin hard water.
See the detergent manufacturer’s instructions for a
further information.
Filling the detergent
Push the latch to open the dispenser and pour in the
detergent.
Close the lid and press it until it locks in place.
The dispenser should be refilled just before the
start of each programme. If the dishes are heavily
soiled, place additional detergent in the pre-wash
detergent chamber.
Using combined detergents
These products should be used according to the
manufacturer’s instructions.
Never put combined detergents into the interior
section or the cutlery basket.
Combined detergents contain not only the
detergent but also rinse-aid, salt replacement
substances and additional components depending
on the combination.
We recommend you do not use combined
detergents in short programmes. Please use powder
detergents instead. If you encounter problems when
using combined detergents, please contact the
detergent manufacturer.
When you stop using combined detergents, make
sure that water hardness and rinse aid settings are
set to the correct level.
Rinse-aid usage
The rinse aid helps to dry the dishes without streaks
and stains. Rinse-aid is required for stain-free utensils
and clear glasses. The rinse aid is automatically
released during the hot rinse phase. If rinse aid
dosage setting set too low, whitish stains remains on
dishes and dishes do not dry and washed clean.
If rinse aid dosage setting set too height, you can see
bluish layers on glass and dishes.
Filling the rinse-aid and setting
To fill the rinse aid compartment, open the rinse-aid
compartment cap. Fill the compartment with rinse
aid to the MAX level and then close the cap. Be
careful not to overfill the rinse aid compartment and
wipe up any spills.
In order to change the rinse aid level, follow the
below steps before turning on the machine:
• Turn on the machine by pressing the On/Off
button.
• Press the Programme button for at least 5
seconds immediately after the machine is turned
on.
• Release the Programme button when “rA” is
shown. Rinse aid level setting follows water
hardness level setting.
Next, the last setting level is displayed.
• The machine will display the last setting.
• Set the level by pushing the programme button.
• Switch off the machine to save the setting.
• The factory setting is “4”.
If the dishes are not drying properly or are spotted,
increase the level. If blue stains form on your dishes,
decrease the level.
Summary of Contents for PD 1046 ET
