background image

Service

31

10

Service

Pfeiffer Vacuum offers first-class service!

Operating fluid and bearing change on the spot by Pfeiffer Vacuum FieldService

Maintenance / repair in the nearby ServiceCenter or ServicePoint

Fast replacement with exchange products in mint condition

Advice on the most cost-efficient and quickest solution

Detailed information, addresses and forms at: 

www.pfeiffer-vacuum.com (Service

).

Maintenance and repair in the Pfeiffer Vacuum ServiceCenter

The following steps are necessary to ensure a fast, smooth servicing process:

Download the forms "Service Request" and "Declaration on Contamination".

1)

Fill out the "Service Request" form and send it by fax or e-mail to your Pfeiffer Vacuum 
service address.

Include the confirmation on the service request from Pfeiffer Vacuum with your ship-
ment.

Fill out the declaration on contamination and include it in the shipment (required!).

Dismantle all accessories.

Drain the operating fluid (applies for turbopumps with pumping speed > 800 l/s).

Leave electronic drive on the pump.

Close the flange openings by using the original protective covers.

If possible, send pump or unit in the original packaging.

Sending of contaminated pumps or devices

No units will be accepted if they are contaminated with micro-biological, explosive or ra-
dioactive substances. “Hazardous substances” are substances and compounds in ac-
cordance with the hazardous goods directive (current version). If pumps are contaminat-
ed or the declaration on contamination is missing, Pfeiffer Vacuum performs 
decontamination at the shipper's expense.

Neutralise the pump by flushing it with nitrogen or dry air.

Close all openings airtight.

Seal the pump or unit in suitable protective film.

Return the pump/unit only in a suitable and sturdy transport container and send it in 
while following applicable transport conditions.

Exchange unit

The factory operating parameters are always preset with exchange units. If you use 
changed parameters for your application, you have to set these again.

Service orders

All service orders are carried out exclusively according to our repair conditions for vacu-
um units and components.

1)

Forms under www.pfeiffer-vacuum.com

Summary of Contents for HiPace 800 P








































Reviews: