manualshive.com logo in svg

PEUGEOT SPEEDFIGHT 3 RS, Workshop Manual

The PEUGEOT SPEEDFIGHT 3 RS, a stylish and powerful scooter, is a true masterpiece of design and performance. Discover its exceptional features and technical specifications in our detailed, user-friendly manual. Download the brochure and manual for free from our website and unleash the full potential of this extraordinary vehicle.

Share
Download
background image

TABLE OF CONTENTS

1

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Motocycles

TABLE OF CONTENTS

TABLE OF CONTENTS..................................................................................................................................... 1

PRODUCTS DANGER SYMBOLS USED......................................................................................................... 4

CHARACTERISTICS......................................................................................................................................... 6

Engine........................................................................................................................................................6

Capacities ..................................................................................................................................................6

Chassis ......................................................................................................................................................7

Dimensions and weight.............................................................................................................................. 7

Tyres .......................................................................................................................................................... 7

Brakes ........................................................................................................................................................8

SERVICE SCHEDULE AND COMMISSIONING............................................................................................... 9

To be checked at each service...................................................................................................................9

Service operations. ..................................................................................................................................10

Time required for maintenance ................................................................................................................10

Battery preparation (Except battery without maintenance)* ....................................................................11

Installing the battery vapour vent hose. ...................................................................................................11

New machine preparation ........................................................................................................................11

SPECIAL IMPORTANT POINTS..................................................................................................................... 12

Oil and fuel...............................................................................................................................................12

TIGHTENING TORQUES ................................................................................................................................ 13

Engine part ..............................................................................................................................................13

Body panels .............................................................................................................................................13

Cycle part.................................................................................................................................................14

Standard ..................................................................................................................................................14

SPECIAL TOOLS ............................................................................................................................................ 15

STANDARD TOOLS........................................................................................................................................ 15

LOCATION OF COMPONENTS...................................................................................................................... 16

BODY PANELS ............................................................................................................................................... 17

Location of body components ..................................................................................................................17

Body component sequence of disassembly.............................................................................................18

Removal of the storage compartment......................................................................................................19

Removal of the rear cover assembly and mudflap ...................................................................................20

Removal of handlebar fairing ...................................................................................................................21

Removal of the front top shield panel.......................................................................................................22

Removal of the rear shield panel .............................................................................................................22

Summary of Contents for SPEEDFIGHT 3 RS





























































Reviews:

No comments

Related manuals for SPEEDFIGHT 3 RS

Jetson Triton Manual preview
Triton
Brand: Jetson Pages: 24
Olsson and Brothers Unique User'S Manual And Garantee preview
Unique
Brand: Olsson and Brothers Pages: 25
URBANGLIDE RIDE 69L Translation Of The Original Instructions preview
RIDE 69L
Brand: URBANGLIDE Pages: 54
NASA MERCURY10-10W User Manual preview
MERCURY10-10W
Brand: NASA Pages: 68
Fusion Scoot 4in1 Owner'S Manual preview
Scoot 4in1
Brand: Fusion Pages: 2
Mortch Solana User Manual preview
Solana
Brand: Mortch Pages: 22
MBK FlameX NXC125 Owner'S Manual preview
FlameX NXC125
Brand: MBK Pages: 76
Volvo Truck Service Manual preview
Truck
Brand: Volvo Pages: 10
VESPA LXV 125 ie 2013 Manual preview
LXV 125 ie 2013
Brand: VESPA Pages: 88
Landlex S300x RS Operation Manual preview
S300x RS
Brand: Landlex Pages: 10
Muvi Torrot T L1e-B Owner'S Manual preview
Torrot T L1e-B
Brand: Muvi Pages: 47
SMC Networks Navigator 100cc User Manual preview
Navigator 100cc
Brand: SMC Networks Pages: 24
KUGOO B1 Instructions Manual preview
B1
Brand: KUGOO Pages: 35
Lime Generation 3.0 Instructions Manual preview
Generation 3.0
Brand: Lime Pages: 15
UJET UJET User Manual preview
UJET
Brand: UJET Pages: 116
Lambretta 150 Li Instruction Booklet preview
150 Li
Brand: Lambretta Pages: 43
Daymak Rickshaw Deluxe User Manual preview
Rickshaw Deluxe
Brand: Daymak Pages: 27
Razor C25 Owner'S Manual preview
C25
Brand: Razor Pages: 16

Brands by name

Popular brands

Load more brands