background image

 

17 

 
INSTALLATION INSTRUCTIONS 

 

GAS HOOK-UP 

 
Only the pressure regulator and hose assembly supplied with the grill should be used. Any replacement 
pressure regulator and hose assembly must be specified by the grill manufacturer. 
 
Total gas consumption (per hour) of the 720-0335 liquid propane gas grill with all burners set on 

HI

Main burners              42,000 BTU/Hr.                     
Rear burner 

            10,000 BTU/Hr. 

Searing burner             18,000 BTU/Hr. 
Side burner 

            12,000 BTU/Hr. 

Total 

 

            82,000 BTU/Hr. 

 
The installation of this appliance must conform with local codes or, in the absence of local codes, with 
either the National Fuel Gas Code, ANSI Z223.1

/NFPA 54, National Gas Propane Installation Code, CSA 

B149.2.

 

Installation in Canada must be in accordance with the Standard CSA B149.2 (installation code for gas 
burning appliances and equipment) and local codes. 
 

LIQUID PROPANE CYLINDER REQUIREMENTS  
(20 lb. Cylinder) 

A dented or rusty liquid propane gas cylinder may be hazardous and should be checked by your supplier. 
Never use a cylinder with a damaged valve. The liquid propane cylinder must be constructed and marked 
in accordance with the specifications for liquid propane cylinders by the United States Department of 
Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes 
for Transportation of Dangerous Goods Commission. 
 
The 20 lb. cylinder must have a shut off valve terminating in a valve outlet specified, as applicable, for 
connection type QCC1 in the standard for compressed gas cylinder valve outlet and inlet connection 
ANSI/CGA-V-1. 
 
Storage of an outdoor cooking gas appliance indoor is permissible only if the cylinder is disconnected and 
removed from the outdoor cooking gas appliance. 
 
Manifold pressure: (operating) 10 inches water column (W.C.), (non-operating) 11.2 inches water column 
(W.C.). 
 
The liquid propane cylinder must be fitted with an Overfill Protection Device (OPD). 

  

Remove the plastic valve cover from the liquid propane cylinder. Make sure the grill

s gas hoses do not 

contact the grease tray or grill firebox when the liquid propane cylinder is pushed into the cart. 
 

CONNECTION 

Your grill is equipped with gas supply orifices for use only with liquid propane gas. It is also equipped with 
a high capacity hose/regulator assembly for connection to a standard 20 lb. liquid propane cylinder (18-1/4 
inches high, 12-1/4 inches diameter). 

 

To connect the liquid propane gas supply cylinder: 
1.  The cylinder valve should be in the 

OFF

 position. If not, turn the valve clockwise until it stops. 

2.  Make sure the cylinder valve has the proper type 1 external male thread connections per ANSI Z21.81. 
3.  Make sure the burner valves are in the 

OFF

 position. 

4.  Inspect the valve connections, port and regulator assembly. Look for any damage or debris. Remove 

debris and inspect the hose for damage.  

5.  When connecting the regulator assembly to the valve, use your hand to tighten the nut clockwise until it 

stops. Use of a wrench could damage the quick coupling nut and result in a hazardous situation  

6.  Open the cylinder valve fully by turning the valve counterclockwise. 

PDF 

文件使用

 "pdfFactory Pro" 

试用版本创建

 

www.fineprint.cn

Summary of Contents for 720-0335
































Reviews: