Pentruder Pentpak 3 Operator'S Manual Download Page 35

Page: 35 / 44

Operator’s manual Pentruder RS2 wall saw and Pentpak 3 HFi power pack – Original instructions

Page 35

5.2.2

Indications on RRC display

Contact your Pentruder authorized service workshop for information.

5.2.3

Error codes on RRC display

Error code

Description

Method to reset

Unplug from

mains

supply

Remote

control

Automatic

reset

E1001 Pentpak ambient temperature too high

E1002 Pentpak cooling system, temperature too high

E1201, E1301 Emergency stop or Green button on Pentpak faulty

E1003 Main motor shut off due to slip clutch slipping

E1004, E1604, E1605 Main motor temperature sensor fault

E1008, E1608, E1609 Arm feed motor temperature sensor fault

E1006, E1606, E1607 Travel motor temperature sensor fault

E1200, E1202-E1217

E1300, E1302-E1317 Internal fault, Pentpak control card

E1400 Internal fault, Pentpak control card, radio module

E1600 Saw arm position sensor fault

E1602 Slip clutch sensor fault

E1607 Main motor overheated

E1009 Arm feed motor overheated

E1007 Travel motor overheated

E1699 No communication with saw unit, RS2

E1800 Remote control switch/button/joystick sensor fault

E1801 Remote control battery charging fault

E2100, E2101 Hardware error, Pentpak, drive board, arm feed

E2200, E2201 Hardware error, Pentpak, drive board, travel

E2400, E2401 Hardware error, Pentpak, drive board, main motor

E2102, E2202, E2402 Machine cable failure, open circuit

E2103, E2203, E2403 Machine cable failure, leakage or faulty connection

E2109 Overcurrent detected, arm feed

Joystick

E2209 Overcurrent detected, travel

Joystick

E2409 Overcurrent detected, main motor

E2111, E2211, E2411 Internal fault, Pentpak, drive board

E2113, E2213, E2413 Over voltage, mains supply to Pentpak

E2114, E2214, E2414 Under voltage, mains supply to Pentpak

E2115, E2215, E2415 Internal fault, Pentpak drive board

E2808-E2813 Pentpak rectifier fault

E2850 Under voltage, mains supply to Pentpak

E2851 Over voltage, mains supply to Pentpak

E2853 Line phase missing, mains supply to Pentpak

There are more Error codes which can occur. Contact your Pentruder authorized service workshop for information.

Summary of Contents for Pentpak 3













































Search results

Summary of Contents for Pentpak 3

Reviews:

Related manuals for Pentpak 3

Brands by name

Popular brands

Pentruder Pentpak 3, Operator'S Manual

Search results

Summary of Contents for Pentpak 3

Reviews:

Related manuals for Pentpak 3

Brands by name

Popular brands