background image

Safety 2

READ AND FOLLOW 

SAFETY INSTRUCTIONS!

This is the safety alert symbol. When you see 

this symbol on your pump or in this manual, 

look for one of the following signal words and be 

alert to the potential for personal injury.

warns about hazards that will cause 

serious personal injury, death or major property 

damage if ignored.

warns about hazards that can cause 

serious personal injury, death or major property 

damage if ignored.

warns about hazards that will or can 

cause minor personal injury or property damage if 

ignored.
The label NOTICE indicates special instructions 

which are important but not related to hazards.
Carefully read and follow all safety instructions in 

this manual and on pump.
Keep safety labels in good condition. 
Replace missing or damaged safety labels.

California Proposition 65 Warning

 This product and related accesso-

ries contain chemicals known to the State of 

California to cause cancer, birth defects or other 

reproductive harm.

RULES FOR SAFE 

INSTALLATION AND 

OPERATION

Read t he Owner’s Manual and Rules for Safe 

Operation and Installation Instructions carefully. 

Failure to follow these Rules and Instructions could 

cause serious bodily injury and/or property damage.
Install system according to local codes.
Always test water from well for purity before using. 

Check your local health department for testing  

procedure.
Before installing or servicing your tank, BE SURE 

pump electric power source is disconnected.
BE SURE your pump electrical circuit is properly 

grounded.
Remove bleeder orifices, air volume controls or 

other air charging devices in existing system.

To prevent possible serious or fatal 

injury and/or damage to equipment, system pres-

sure must be less than 100 pounds per square inch 

(PSI)(6.9 Bar) under any circumstances. Failure to 

follow this instruction can result in tank blowup.  

If system discharge pressure can exceed 100 PSI 

(6.9 Bar), install a relief valve capable of passing 

the full pump volume at 100 PSI (6.9 Bar).

Hazardous pressure. Read owner’s 

manual before attempting to install, operate, or ser-

vice this tank. To avoid possible equipment failure, 

severe injury, and property damage, do not allow 

pump, tank, or piping system to freeze.

Limited Warranty

F.E. MYERS warrants to the original consumer purchaser (“Purchaser” or “You”) of the products listed below, that they will be free from defects 
in material and workmanship for the Warranty Period shown below. 

Product

Warranty Period

Jet pumps, small centrifugal pumps, submersible pumps 
and related accessories

whichever occurs first: 
12 months from date of original installation, 
 or 18 months from date of manufacture

Fibrewound Tanks

5 years from date of original installation

Steel Pressure Tanks

5 years from date of original installation

Sump/Sewage/Effluent Products

12 months from date of original installation, 
or 24 months from date of manufacture

Our warranty will not apply to any product that, in our sole judgement, has been subject to negligence, misapplication, improper installation, 
or improper maintenance. Without limiting the foregoing, operating a three phase motor with single phase power through a phase converter 
will void the warranty. Note also that three phase motors must be protected by three-leg, ambient compensated, extra-quick trip overload relays 
of the recommended size or the warranty is void.
Your only remedy, and F.E. MYERS’s only duty, is that F.E. MYERS repair or replace defective products (at F.E. MYERS’s choice). You must pay all 
labor and shipping charges associated with this warranty and must request warranty service through the installing dealer as soon as a problem 
is discovered. No request for service will be accepted if received after the Warranty Period has expired. This warranty is not transferable.
F.E. MYERS SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.
THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, 
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE 
FOREGOING LIMITED WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of an implied 
warranty, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You may also have other 
rights which vary from state to state.
This Limited Warranty is effective June 1, 2011 and replaces all undated warranties and warranties dated before June 1, 2011.

F.E. MYERS 

293 Wright Street, Delavan, WI  53115 

Phone: 888-987-8677 • Fax: 800-426-9446 • www.femyers.com

In Canada: P. O. Box 9138, 269 Trillium Dr., Kitchener, Ontario N2G 4W5 

Phone: 519-748-5470 • Fax: 888-606-5484

Summary of Contents for Myers MS Series

























Reviews: