background image

- 6 -

Mounting the Electric Compressor and Tank

Mounting Foam Nozzles or Air-Liquid Mixers

The electric compressor and tank can be 
mounted on the machine in two different 
ways (see illustration at left). 

Option 1

When joining the electric compressor unit “D” to the
foaming liquid tank “A,” place the spacers “B” and
fixing bracket “C” between them.

Option 2

Install the compressor unit “D” and the tank “A” in
different locations according to your own needs. 

In this case, it is possible to secure the bed of the
electric compressor to the machine, or to use the
bracket “C”. 

The foam nozzle or air-liquid mixers must be
mounted at the end of the booms as follows:

• On boom “A”, make 2 holes at a center distance

of 4.5” using a drill with a bit Ø 6 mm.

• Secure the supports “B” to the boom using M6

screws of an appropriate length.

• Insert the foam nozzle “H” on the knurled portion

of the support rod “F” and secure with the screw
supplied “G.”

• Insert the support rod “F” into the supports “B.”

• Mount and tighten the wing nut “E” on the spacer

“D.”

In this way, the foam nozzle will “

rotate.

To make the foam nozzle “

fixed

,” mount and tighten

the screw “C” on the support “B.”

• Repeat the above operations for the other boom

as well.

Mounting foam nozzle onto the boom

Summary of Contents for Hypro ARAG 520005





















Reviews: