background image

740 EAST 9TH STREET 

490 PinEbuSH RoAd, uniT #4 

ASHLAnd, oHio, uSA 44805 

CAMbRidGE, onTARio, CAnAdA n1T 0A5 

419-289-1144 800-363-PuMP 

WWW.HYdRoMATiC.CoM

Warranty Rev. 12/13

STANDARD LIMITED WARRANTY

Pentair Hydromatic

®

 warrants its products against defects in material and workmanship for a period of 12 months 

from the date of shipment from Pentair Hydromatic or 18 months from the manufacturing date, whichever  

occurs first – provided that such products are used in compliance with the requirements of the Pentair Hydromatic  

catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive-free,  

noncorrosive liquids. 

during the warranty period and subject to the conditions set forth, Pentair Hydromatic, at its discretion, will repair 

or replace to the original user, the parts that prove defective in materials and workmanship. Pentair Hydromatic 

reserves the right to change or improve its products or any portions thereof without being obligated to provide such 

a change or improvement for prior sold and/or shipped units.

Start-up reports and electrical schematics may be required to support warranty claims. Submit at the time of start up 

through the Pentair Hydromatic website: http://forms.pentairliterature.com/startupform/startupform.asp?type=h.  

Warranty is effective only if Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing 

devices must be hooked up, functional and monitored or this warranty will be void. Pentair Hydromatic will cover 

only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be 

responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight 

expenses to and from the factory or an authorized Pentair Hydromatic service facility.
This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly install, operate or 

maintain the unit in accordance with the printed instructions provided; (b) to failures resulting from abuse, accident 

or negligence; (c) to normal maintenance services and parts used in connection with such service; (d) to units that 

are not installed in accordance with applicable local codes, ordinances and good trade practices; (e) if the unit is 

moved from its original installation location; (f) if unit is used for purposes other than for what it is designed and 

manufactured; (g) to any unit that has been repaired or altered by anyone other than Pentair Hydromatic or an 

authorized Pentair Hydromatic service provider; (h) to any unit that has been repaired using non factory specified/

oEM parts.

Warranty Exclusions: PEnTAiR HYdRoMATiC MAKES no EXPRESS oR iMPLiEd WARRAnTiES THAT EXTEnd 

bEYond THE dESCRiPTion on THE FACE HEREoF. PEnTAiR  HYdRoMATiC SPECiFiCALLY diSCLAiMS THE 

iMPLiEd WARRAnTiES oF MERCHAnTAbiLiTY And FiTnESS FoR AnY PARTiCuLAR PuRPoSE.

Liability Limitation: in no EVEnT SHALL PEnTAiR  HYdRoMATiC bE LiAbLE oR RESPonSibLE FoR 

 

ConSEQuEnTiAL, inCidEnTAL oR SPECiAL dAMAGES RESuLTinG FRoM oR RELATEd in AnY MAnnER To  

AnY  PEnTAiR  HYdRoMATiC PRoduCT oR PARTS THEREoF. PERSonAL inJuRY And/oR PRoPERTY dAMAGE  

MAY RESuLT FRoM iMPRoPER inSTALLATion. PEnTAiR  HYdRoMATiC diSCLAiMS ALL LiAbiLiTY, inCLudinG 

LiAbiLiTY undER THiS WARRAnTY, FoR iMPRoPER inSTALLATion. PEnTAiR  HYdRoMATiC RECoMMEndS 

inSTALLATion bY PRoFESSionALS.

Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of incidental or 

consequential damages and therefore such limitations may not apply to you. no warranties or representations at any 

time made by any representatives of Pentair Hydromatic shall vary or expand the provision hereof.

Summary of Contents for Hydromatic Novus 4000

















Reviews: