manualshive.com logo in svg

Pentair BIOSHIELD 522635, Installation And User Manual, Page: 5 / 16

Share
Download
Pentair BIOSHIELD 522635 Installation And User Manual Download Page 5

2

PRE-INSTALLATION INSPECTION

 

All Bioshield

®

 UV Disinfection Sterilizers are packaged complete, with all necessary components that are required to 

operate the unit. When unpacking your Bioshield UV system, we recommend that a complete component inventory be 
taken to ensure that all components are included and accounted for, prior to installation.    
Bioshield units have their serial number labels located on the UV vessel and on the power supply label.       
The model number of your UV unit can be found in two locations:

1.  On the bar code label at the end of the box.
2.  On the label placed in the middle of the UV Vessel.

Component Diagram

Please review the component diagram below. Unpack your UV system, and lay out the packaged components for 
inspection. Please review the information listed in this section to become familiar with the equipment’s various parts. 

Power Supplies

P/N 523033: 150W (120V) Models
P/N 523053: 150W (240V) Models

P/N 523032: 50W, 80W & 120W Models

BIOSH IELD

®

 U V D isinfection Sterilizer Installation and U ser’

s Guide

Summary of Contents for BIOSHIELD 522635

















Reviews:

No comments