background image

8 • WHOLE HOUSE CARBON FILTRATION SYSTEM

QUICK START GUIDE: SYSTEM START-UP INSTRUCTIONS CONTINUED

1.   

Connect the unit to the existing plumbing: 

 

       

 

 

 

(Facing the front of the system, INLET is on the LEFT – OUTLET is on the RIGHT) 

 

 

 

 

             

 

 

              

The

 

bypass is only hand tightened at the factory and must be fully tightened and checked for leaks by 

the installer.

 

            

 

 

             

Connect the drain line to a proper location; adhere to ALL LOCAL and STATE CODES. When turning the 
water back on, leave the system in bypass mode and then the turn water on to the house and check for 
leaks. Run the cold water in bathtub or outdoor faucet to flush debris and air from the lines. (Bathtubs 
do not have aerators that may plug with debris.) Then, once the programming is complete, follow the 
start up procedure starting at step 8.

2.   

Understanding the face plate.

 

         

There are 3 buttons on the face of the unit. The button on the left with the 2 arrows in a circle is called 
the scroll button. The buttons to the right are the up and down buttons.

3.     

Programing the System:

 

          

To begin, verify that the control is in the service mode.   

 

 

 

 

 

 Press and hold the DOWN arrow for 5 seconds; the control will display: SYSTEM CHECK 

 

 

Then enter the following code by pressing and releasing the following buttons.   

 

 

DOWN, DOWN, SCROLL, DOWN,

 THIS MUST BE DONE WITHIN 10 SEC. or the control will return to 

the home screen. The screen will display 

“CAPACITY: 1200 GL”

, by using the UP or DOWN arrow. 

The number will advance by 100 each time you press the arrow. The factory setting is fine for most 
applications. 

            

 

 

            

4.    Press the SCROLL button to advance to the next setting.  

 

 

 

 

 

The screen will read 

“CHANGE PHONE? NO”

 use DOWN button change to 

“YES”

 Press the SCROLL 

button 1 time and the 1st number will flash. 

 

 

 

 

 

 

 

Use the UP or DOWN button to program your phone number to display. After each number press the 
SCROLL button 1 time to advance to the next number. After setting all the numbers, press SCROLL to 
advance to the next setting.

5.     The control will display 

“TIME OF DAY”

, press the UP or DOWN arrow to program the time of day.

6.     Press the SCROLL button to advance to the next setting. The control will then display 

“Go to ADVANCED 

menu? No” 

If you want to go to advanced settings, press the UP or DOWN arrow, change to “YES” 

and press the SCROLL button (Default settings on ADVANCED MENU will not need to be changed for 
most 

applications).           

*The ADVANCED MENU consist of 

RESET AVERAGE:

 NO, 

RESERVE CAPACITY:

 VARIABLE, 

TIME OF 

REGENERATIONS:

 1 AM, 

DAYS OVERRIDE:

 OFF, 

BACKWASH:

 10min, 

BRINE/SLOW RINSE:

 0min,  

FILL/RINSE:

 3min

7.     If you don’t want to access the advanced settings, leave at “NO”. Press SCROLL button 1 time. The 

control will display

 “EXIT: PRESS

 ↓

, press DOWN to exit installer’s program level. The Time of day and 

rolling message “For Service, Call (your number)” will be displayed.

WARNING

Summary of Contents for 1.0































Reviews: