Pentair Pool Products Nocchi CPS 10 Use And Maintenance Manual Download Page 19

 

Page 17 of 30

RIP F 

Restart type 

Parameter used to define how the restarting mechanism 
works. If set to FIN, the module will go into a definitive 
alarm after the fourth attempt. If sent to CICL, it will 
attempt to restart indefinitely using the interval specified 
during the fourth attempt.

FIN FIN 

CICL 

RIP T 

Intervention time 

Waiting time after restarting within which pressure must 
return to above the minimum threshold level for lack of 
water. (seconds)

15 5 

300 

ORE P 

Hours running 

Number of hours the pump has been running.

N.A. N.A. 

N.A. 

SCA T 

Exchange time  

Parameter indicating the amount of time a pump must run 
for. Once this value has been reached, the pump will stop 
and a second pump will commence working. This 
parameter is expressed in minutes until it reaches 60, 
after which it is expressed in hours. The difference is 
indicated by the presence of an "H" for hours and an "M" 
for minutes. 
Must be set to primary for a unit or for twin pumps.

0 0 

168 

SCA S 

Exchange time 
mode 

Pumps are exchanged once the SCAT parameter has 
been reached: 

T1:

 The active pump is switched off first, before the 

second pump starts up 

T2:

 The second pump is switched off first, before the first 

pump starts-up.

1 1 

FP

PWM frequency 

Frequency of the PWM which controls the motor.

15.9 5.1 

15.9 

INSTALLATION PARAMETERS 

TAB 

Anti-locking 

Amount of time the pump is inactive. Once this amount of 
time has expired, the pump will start up for 15 seconds at 
maximum frequency. Then, the frequency will be slowly 
lowered until the minimum set frequency is obtained. This 
parameter is expressed in minutes until it reaches 60, 
after which it is expressed in hours. The difference is 
indicated by the presence of an "H" for hours and an "M" 
for minutes.

0 0 

 

999 

5.4  MANUAL START OF MOTOR/PRIMING 

This procedure is applicable when you want to manually start the system or prime the pump. 

 

It is possible to manually start the motor by pressing the following sequence of buttons: 

Buttons sequence with pump off 

The pump remains on until the last button is pressed

  

Last button pressed for 10 seconds 

 

17  - GB -

44

Summary of Contents for Nocchi CPS 10






























Reviews: