Penn F263 Series Installation Instructions Manual Download Page 5

F263 Series Liquid Level Switches Installation Instructions

5

 Setup and Adjustments    

Checkout Procedure

Before applying power, ensure that installation and wiring connections are made to job specifications.

After making all necessary adjustments and electrical connections, put the system into operation and observe at 
least three complete operation cycles before leaving the installation site.

Operation

The F263 Float Switch controls water levels to within approximately 1/2 in. (13 mm).

When the liquid level falls approximately 1/2 in. (13mm) below the height at which the switch is installed, the switch 
closes the red contact (common) to the blue contact. See Figure 6 and Figure 7.

!

CAUTION: Risk of Property Damage.

Do not set the switch lower than the factory setting. The switch is factory set at 
approximately the minimum flow rate. A lower setting may result in the switch failing to 
return to a no-flow position which may result in damage to the controlled equipment or other 
property.

MISE EN GARDE : Risque de dégâts matériels.

Ne pas régler le commutateur sur une valeur inférieure au paramètre d'usine. Le 
commutateur est réglé en usine sur une valeur correspondant environ au débit minimum. 
Un réglage sur une valeur inférieure risque d'empêcher le commutateur de revenir sur une 
position « aucun-débit », ce qui risque d'endommager l'équipement contrôlé ou de 
provoquer d'autres dégâts matériels.

!

CAUTION: Risk of Property Damage.

Do not attempt to change sealed settings. Attempted adjustment may damage the control 
or cause loss of calibration or other property damage.

MISE EN GARDE : Risque de dégâts matériels.

Ne pas essayer de modifier la position des éléments de réglage bloqués. Toute tentative de 
réglage risque d'endommager le dispositif de contrôle ou de provoquer la perte des valeurs 
d'étalonnage ou d'autres dégâts matériels.

IMPORTANT:

All F263 switches are factory-set and factory-sealed. 

Do not

 attempt to change the factory 

settings. Changing the factory settings voids the warranty.

Figure 5:   Circuit for Controlling Dump Levels 

R

R

Y

Y

B

B

Pump Out

R1

R2

Pump

R

High Level

F263 Switch

Low Level

F263 Switch

L

L

FI

G

:d

m

p_l

vl

_c

ntr

l

Summary of Contents for F263 Series









Reviews: