background image

N. 

For Doors with adjustable hinges:

 The hinges can be used to move the panel side 

to side by moving all hinges in the same direction or the hinges can slightly rotate the 
panel by adjusting the hinges in opposite directions. Use a T20 Torx wrench to turn 
the center screw clockwise (+) to increase the space between the hinge side of the 
frame and door panel. Turn the center screws counter-clockwise (-) to decrease the 
space between the hinge side of the frame and the door panel .

Note: Do not adjust the hinge with the top and bottom screws loose; this could 
force the hinge to adjust beyond its design capability which can cause the hinge 
to bind, damage the hinge and/or pull out the screws. A 3/4 turn of the center 
screw provides approximately 5/32" adjustment. 

O. 

On doors with a lock strike in the 
side,

 drill a 1/8" diameter x 2" deep 

pilot hole into the rough opening 
through the two pre-drilled holes in 
the frame. One pre-drilled frame hole 
is located in the center lock strike 
hole and the other is the upper frame 
corner installation hole approximately 
8" from the top of the door frame 
head. Insert a #8 x 3" screw (provided) 
into the pilot hole making sure it 
passes through the shim and into the 
rough opening framing.

Note: This step does not apply to 
center latching double doors.

DOORS •

 ALL

 DOORS •

 ALL

 DOORS •

 ALL

 DOORS •

 ALL

 DOORS •

 ALL

 DOORS •

 ALL

 DOORS

4

INTEGRATING THE DOOR TO THE
WATER RESISTIVE BARRIER

A. 

Apply a corner bead of sealant at the point 

where the brickmould or fl at casing contacts 
the wall along the head and jambs. Also apply 
a bead of sealant at each end of the head 
brickmould.

B. 

Install the head fl ashing.

C. 

Apply a piece of fl ashing tape

 

over the head fl ashing as shown.

&YUFSJPS

"

4A

#

)FBEnBTIJOH

4FBMBOU

4B

&YUFSJPS

%

4D

$

)FBEnBTIJOH

'MBTIJOHUBQF

4C

&

4E

D. 

Fold down the top fl ap of the 
water resistive barrier. 

Cut 

the water resistive barrier so it 
covers the vertical leg of the 
head fl ashing, however does not 
lap onto the horizontal leg of the 
head fl ashing.

E. 

Apply fl ashing tape to the 
diagonal cuts

. Cut two pieces of 

fl ashing tape at least 1" longer 
than the diagonal cuts in the 
water resistive barrier. Apply the 
tape covering the entire diagonal 
cut in the water resistive barrier 
at both upper corners of the 
brickmould/fl at casing.

3O

3O

3O

~8”

Head

*

A

M

B

Summary of Contents for 818K0100

















Reviews: