background image

Knowledge of proper procedures is essential to the 
safe operation of electrically energized equipment.  In 
accordance with generally accepted product safety labeling 
guidelines for potential hazards, the following signal words 
and symbols may be used throughout this manual.

Used to indicate the presence 

of a hazard that will cause 

severe personal injury, death, 

or substantial property 

damage if the warning 

included with this symbol 

is ignored.

Used to indicate the presence 

of a hazard that can cause 

personal injury, possible 

death, or major property 

damage if the warning 

included with this symbol 

is ignored.

Used to indicate the presence 

of a hazard that can or will 

cause minor or moderate 

personal injury or property 

damage if the warning 

included with this symbol 

is ignored.

Used to indicate the presence 

of a hazard that can or will 

cause minor personal injury, 

property damage, or a 

potential unsafe practice if the 

warning included with this 

symbol is ignored.

Used to notify personnel of 
installation, operation, or 
maintenance information that is 
important but not hazard related.

1.  Pedigo blanket warmers are intended for warming 

cotton blankets ONLY. No other use for this device is 
authorized or recommended.

2.  This device is intended for use in commercial 

establishments where all operators are familiar with 
the purpose, limitations, and associated hazards of this 
device.  Operating instructions and warnings must be 
read and understood by all operators and users.

3.  Any troubleshooting guides, component views, and 

parts lists included in this manual are for general 
reference only and are intended for use by qualified 
technical personnel.

4.  This manual should be considered a permanent part of 

this device.  This manual and all supplied instructions, 
diagrams, schematics, parts lists, notices, and labels 
must remain with the device if the item is sold or moved 
to another location.

NOTE:

SAFETY PROCEDURES A N D   P R E C A U T I O N S

2

N O T E

For equipment delivered for use 
in any location regulated by the 
following directive:
DO NOT DISPOSE OF ELECTRICAL 
OR ELECTRONIC EQUIPMENT WITH 
OTHER MUNICIPAL WASTE. 

N O T E

Pedigo warmers should not be left 

unattended for periods of more than 24 hours.  

In case of absences longer than 24 hours, 

disconnect the warmer from its power source.

Summary of Contents for P-2010-S



















Reviews: