background image

Traction Dot

3-Piece Screw

Traction Plate

Velcro Strips

Allen Screw

Allen wrench

Adjustment Knob

Wing Bolt

Traction Plate / Traction Dots

The  Traction  Plate  adjusts  to  a  variety  of  grip/slide 

configurations. To change the position of the Traction Dots, 

use the Multi-Function Drum Key or Allen wrench (3mm) to 

remove  the  3-Piece  Screw

 

beneath  the  footboard  and 

remove the Traction Plate (Fig.18). Rearrange the Traction 

Dots to your preference and replace the Traction Plate.

Velcro Strips for Slip Prevention

Velcro Strips are provided with P-3002C Double Pedals to 

help  prevent  slipping  when  used  on  carpeted  floors.  To 

apply, peel off the backing on the Velcro Strips and apply 

them in the locations shown. Clean the surfaces thoroughly 

with alcohol and dry completely for best adhesion (Fig.19).

Hoop Clamp System

The  P-3002C  Hoop  Clamp  System  is  designed  with 

Spherical Rubber Grips allowing the front of the bass drum 

to  be  raised  while  keeping  the  pedal  flush  on  the  floor. 

Insert  the  bass  drum  hoop  into  the  Clamp,  and  turn  the 

Wing Bolt to secure.

The Clamp comes preset from the factory to accommodate 

most bass drum hoops but if necessary it can be adjusted 

to fit thicker or thinner hoops. Loosen the Allen Screw on the 

Adjustment Knob with the provided Allen wrench  (2.5mm) 

as shown and tighten or loosen the Adjustment Knob until 

proper  fit  is  achieved  then  re-tighten  the  Allen  Screw 

(Fig.17). If the heel plate of the pedal lifts while playing, try 

loosening the Adjustment Knob to change the angle of the 

Hoop Clamp until the pedal remains flat.

Fig. 18

Fig. 19

Fig. 17

Tip

Setting Examples

The  Aluminum  Traction  Dots  can  be  replaced  with  optional 

NP-283N/7 Rubber Dots for more traction.

Upper Nut

Spring

Lower Nut
Click Lock

Spring Tension Adjustment

The  P-3002C  Demon  Chain  Double  Pedal  features  our 

patented  Click  Lock  spring  tension  retention  system.  To 

increase the spring tension, disable the Click Lock by lifting 

the  lever  upward,  loosen  the  Upper  Nut  and  tighten  the 

Lower Nut until the desired tension is achieved (Fig.16-A). 

To decrease spring tension, disable the Click Lock by lifting 

the  lever  upward,  loosen  the  Upper  Nut  and  loosen  the 

Lower  Nut  until  the  desired  tension  is  achieved.  When  the 

desired spring tension is achieved, tighten the Upper Nut to 

keep the spring tension from loosening then press the Click 

Lock lever down to engage the grooves around the Lower 

Nut until you feel the lever "Click" (Fig.16-B). Before playing, 

make sure that both Upper and Lower Nuts are tight and the 

Click Lock lever is in a vertical position with both sides of 

the lever engaged in the grooves around the Lower Nut.

Fig. 16-B

Fig. 16-A

Summary of Contents for Demon Drive 3000C Series








Reviews: