background image

PINO E -  Building Instruction                                              

                                                             July 2017 

                                                                                                                        

www.pcm.at                                                                                                                                                            

14 

6. BALLAST 

 

In the kit included are: 
- 1x carbon rod 
- 1x steel rod 
- 2x short steel rods 

 

You can use these rods as follows: 

 

1x carbon rod

 for 

weak conditions

 in the front hole.   

Adjust the CG of the plane with this rod inside. 
 

To optimize the center of gravity we have removed this 
front opening.  

 
 
 
 
 

 

1x  1x steel

 

rod 

for 

stronger conditions

 

 

To optimize the center of gravity we have removed the 
foremost opening. 

 

 
 
 
 
 
 
 

 

 

1x carbon, 1x steel rod + 2x short steel

 for 

even stronger 

conditions. 
 

To optimize the center of gravity we have removed the 
foremost opening. 

 

 

 

For extra strong conditions

 you could put into a 

40cm long 

steel rod

 and two 

20cm steel rods behind

. That ballast 

weights 

700g

When you fly with this setting, you have to take care that you 

don`t overload the wing structure

. So use the elevator 

softly, when you fly with that much ballast. Remember also 
that the landings have to be much softer with such an 
additional weight. 

 

Summary of Contents for Pino Medium



















Reviews: