manualshive.com logo in svg

PCE Instruments PCE-HDM 7, User Manual

Share
Download
PCE Instruments PCE-HDM 7 User Manual Download Page 16

 

 

 

©  PCE Instruments 

14 

 

7 

Battery and fuse replacement 

Battery replacement 
WARNING

: To avoid electric shock, remove the test leads from the meter before removing the 

battery/fuse cover. 

1.  Lift up the tilt stand. 

2.  Loosen the two Phillips screws on the battery/fuse cover. 

3.  Remove the battery/fuse cover. 

4.  Replace the batteries with three AAA batteries. 

5.  Observe proper polarity as shown inside battery compartment. 

6.  Install the battery cover and tighten the screws. 

 

WARNING

: To avoid electric shock, do not operate meter until the battery/fuse cover is securely 

fastened to the meter. 

 

Fuse replacement 
WARNING

: To avoid electric shock, remove the test leads from the meter before removing the 

battery/fuse cover. 

1.  Lift up the tilt stand. 

2.  Loosen the two Phillips screws on the battery/fuse cover. 

3.  Remove the battery/fuse cover. 

4.  Gently remove fuse and install new fuse into the holder. 

5.  Always use a UL recognized fuse of the proper size and value: 10 A/600 V (5 x 20 mm) 

fast blow. 

6.  Install the battery cover and tighten the screws. 

 

WARNING

: To avoid electric shock, do not operate meter until the battery/fuse cover is securely 

fastened to the meter. 

 

 

 

Summary of Contents for PCE-HDM 7



















Reviews:

No comments

Brands by name

Popular brands

Load more brands