PCB Piezotronics Larson Davis EPS044 Reference Manual Download Page 48

Page: 48 / 57

NMS044 Reference Manual Rev E

Configuring LD Settings for the RV50X

A-8

A.7 Configuring LD Settings for the RV50X

The RV50X Gateway can only be a functioning communication device if

it is configured with the correct settings. If you purchased a new RV50X

from someone other than Larson Davis—or if it has been reset to

factory defaults—complete the following sections to configure your

system for use with Larson Davis instruments.

In this section:

•

A.7.1 Logging In to ACEmanager

•

A.7.2 Configuring LD Settings Using the Template File

•

A.7.3 Configuring LD Settings Without the Template File

A.7.1 Logging In to ACEmanager

Step 1

Attach the USB to mini cable from the PC to the gateway. See

Figure 2-4

Connecting to RV50X

Step 2

Open a web browser.

Step 3

Enter

http://192.168.14.31:9191

into the address bar.

Step 4

user

” with default password “

12345

”.

FIGURE A-3

Sierra Wireless Login

Step 5

Take note of the device’s firmware version. Update to the latest version if

needed.

Updating Firmware to the Latest Version (Optional)

Go to

http://source.sierrawireless.com/

Select the name of your device, then select

Firmware Package

If needed, download and update the firmware according to the

manufacturer's instructions.

Step 5

Change your password.

Summary of Contents for Larson Davis EPS044


























































Search results

Summary of Contents for Larson Davis EPS044

Reviews:

Related manuals for Larson Davis EPS044

Brands by name

Popular brands

PCB Piezotronics Larson Davis EPS044, Reference Manual

Search results

Summary of Contents for Larson Davis EPS044

Reviews:

Related manuals for Larson Davis EPS044

Brands by name

Popular brands