PCB Piezotronics 208C01, Installation And Operating Manual

Page: 16 / 17

Model Number
208C01
ICP® FORCE SENSOR
Revision: K
ECN #: 45224
Performance ENGLISH SI
Sensitivity(± 15 %) 500 mV/lb 112,410 mV/kN
Measurement Range(Compression) 10 lb 0.04448 kN
Measurement Range(Tension) 10 lb 0.04448 kN
Maximum Static Force(Compression) 60 lb 0.27 kN
Maximum Static Force(Tension) 60 lb 0.27 kN
Broadband Resolution(1 to 10,000 Hz) 0.0001 lb-rms 0.00045 N-rms [2]
Low Frequency Response(-5 %) 0.01 Hz 0.01 Hz [3]
Upper Frequency Limit 36,000 Hz 36,000 Hz [4]
Non-Linearity ≤ 1 % FS ≤ 1 % FS [5]
Environmental
Temperature Range -65 to +250 °F -54 to +121 °C
Temperature Coefficient of Sensitivity ≤ 0.05 %/°F ≤ 0.09 %/°C
Electrical
Discharge Time Constant(at room temp) ≥ 50 sec ≥ 50 sec
Excitation Voltage 18 to 30 VDC 18 to 30 VDC
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance ≤ 100 Ohm ≤ 100 Ohm
Output Bias Voltage 8 to 12 VDC 8 to 12 VDC [1]
Spectral Noise(1 Hz) 0.0000126 lb/ √ Hz 0.0000562 N/ √ Hz [2]
Spectral Noise(10 Hz) 0.0000042 lb/ √ Hz 0.0000189 N √ Hz [2]
Spectral Noise(100 Hz) 0.0000015 lb/ √ Hz 0.0000067 N/ √ Hz [2]
Spectral Noise(1000 Hz) 0.0000005 lb/ √ Hz 0.0000023 N/ √ Hz [2]
Output Polarity(Compression) Positive Positive
Physical
Stiffness 6 lb/µin 1.05 kN/µm [2]
Size (Hex x Height x Sensing Surface) 0.625 in x 0.625 in x 0.500 in 15.88 mm x 15.88 mm x 12.7 mm
Weight 0.80 oz 22.7 gm
Housing Material Stainless Steel Stainless Steel
Sealing Hermetic Hermetic
Electrical Connector 10-32 Coaxial Jack 10-32 Coaxial Jack
Electrical Connection Position Side Side
Mounting Thread 10-32 Female 10-32 Female
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Group, Inc.
N
- Negative Output Polarity
Output Polarity(Compression) Negative Negative
W
- Water Resistant Cable
NOTES:
[1]Sensor contains protected electronics which may cause long 'turn-on" times.
[2]Typical.
[3]Calculated from discharge time constant.
[4]Estimated using rigid body dynamics calculations.
[5]Zero-based, least-squares, straight line method.
[6]See PCB Declaration of Conformance PS023 for details.
SUPPLIED ACCESSORIES:
Model 080A81 Thread Locker (1)
Model 081B05 Mounting Stud (10-32 to 10-32) (2)
Model 084A03 Impact Cap (1)
Model M081A62 Mounting stud, 10-32 to M6 x 1, BeCu with shoulder (2)
3425 Walden Avenue, Depew, NY 14043
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com
[6]
OPTIONAL VERSIONS
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
Entered: LK Engineer: MJK Sales: KWW Approved: APB Spec Number:
Date: 3/29/2016 Date: 3/29/2016 Date: 3/29/2016 Date: 3/29/2016
8625