background image

1

Motherboard User’s Guide

Chapter 1 Introduction

This motherboard has a 

Socket-939 

supporting the newest and advanced 

AMD

Athlon 64/Athlon 64 FX

 

(K8)

 processors.

This motherboard integrates the 

VIA K8M800

 Northbridge and 

VT8237

Southbridge that supports the 

Serial ATA

 interface for high-performance and

mainstream desktop PCs, and the built-in 

USB 2.0

 providing higher bandwidth.

It implements 

Universal Serial Bus Specification Revision 2.0 

and is

compliant with 

UHCI 1.1

 and 

EHCI 0.95

.

It supports 6-channel 

AC’97 Audio Codec

 and provides one 

 IDE Ultra DMA

133

/100/66

 

channel. It has three 32-bit 

PCI

 slots, one 

8X AGP

 slot, one 

CNR

(Communications and Networking Riser) slot, and supports the onboard

10BaseT/100BaseTX Network

 interface (optional). In addition, this

motherboard has a full set of I/O ports including two PS/2 ports for mouse and
keyboard, one serial port, one parallel port, one VGA port, one LAN port
(optional), four back-panel 

USB2.0

 ports, and three audio jacks for microphone,

line-in and line-out.  Onboard USB header(s) can provide extra ports by
connecting the Extended USB Module to the motherboard.

This motherboard is a 

MicroATX size

 motherboard and has power connectors

for an ATX power supply.

Key Features

The key features of this motherboard include:

Socket-939 Processor Support

Supports AMD 

Athlon 64/Athlon 64 FX

 

(K8)

 processors

Chipset

There are 

VIA K8M800 Northbridge

 and 

VT8237 Southbridge

 in this chipset

in accordance with an innovative and scalable architecture with proven reliability
and performance.

Defines Highly Integrated Solutions for High-Performance Workstation

& PC Desktop Designs -- High-performance North Bridge with
HyperTransport interface to AMD™ K8 CPU plus AGP 8X external
bus to external Graphics Controller plus high-speed V-Link interface to
South Bridge

High Performance HyperTransport CPU Interface -- Processor interface

via HyperTransport interface

Full Featured Accelerated Graphics Port (AGP) Controller

− −

 AGP v3.0 compliant 8X / 4X transfer mode with Fast Write Support

− −

 Pipelined split-transaction long-burst transfers up to 2.1 GB/sec (4

bytes x 533 MHz)

Summary of Contents for A21G





































Reviews: