background image

 

 

18 Installation of the cascade controller 

52 

99E13331xx-mub-en - V08 

2022/07 

Now, assign the correct controller types to the other modules. If a controller was marked as a 
server, the menu items of the commissioning are shortened because the main parameters are 
set via the client.  

 

COMMISSIONING 

Language 

 

Controller type 

 

Finish with protocol 

 

Finish without protocol 

 

To complete the commissioning at the servers, confirm 
the items 

Finish with protocol

 (for this, a USB flash drive 

must be connected to the controller) or 

Finish without 

protocol. 

Now, at the client, go to the menu item 

Scan Modbus

. In the following, a search run starts which 

identifies the connected controllers in the cascade system. If a server was detected by the 
client, it is marked with 

OK.

 After that, leave the menu via the 

Back

 button.  

Now, the automatic synchronisation of all controllers in the cascade starts. When it is 
completed, the message "

Synchronisation finished

" is displayed. 

Please note: If the number of the communicating domestic hot water modules is modified within 
the cascade (e.g. server X is being maintained) or the MB3.10 is switched on or off,  

Scan Modbus

 must be repeated to specify the exact number of the participants within the 

Modbus network. 

 

 

SCAN MODBUS 

STATUS 

Server 1 

 

OK 

Server 2 

 

OK 

Server 3 

 

OK 

MB3.10 

 

--- 

 

   

 
 

 
 

 
 

 

SYNCHRONISE

 

 

Synchronisation 

completed 

 

………OK…....

 

 

 

 
 

Summary of Contents for FC3.10

















































































Reviews: