background image

INSTALLING THE BATTERY 

The battery, sold separately, slides into the channel on the underside of the unit, covering the AC input, 
and locking into place.

BATTERY LIFE INDICATOR

The battery life is indicated by the small lights on the rear of the battery and are illuminated when the 
button is pushed.

A fully charged battery will provide approximately 250 full power flashes before needing to be recharged. 
The LED modeling light of the LINK can be powered via the battery however, be aware if running at full 
power the battery will last about 45 min. (assuming no flash use during this time).

REMOVING THE BATTERY 

The battery can be removed from the LINK by pressing down on the tab and sliding out from the channel. 
It is recommended to 

remove the battery prior to transporting or storing the LINK

EXPECTED LIFETIME

The battery should last between 2 - 3 years under normal use.

MAINTAINING THE BATTERY

If you aren’t going to use the battery for an extended period of time (>3 months) it is best to leave the 
batteries partially discharged (40-60% of full charge) rather than fully charged.

LINK BATTERY

The battery charger, sold separately, can charge up to two LINK batteries consecutively. The charger has 
indicator lights notifying what charging state the battery is in. When two batteries are charging, one will 
charge fully, and then the second will begin to charge. It takes approximately 90 min. for a depleted battery 
to be charged to full.

CHARGING THE BATTERY

BATTERY LIFE INDICATOR

Side View

Top View

Rear View

BATTERY LATCH

Rear View w/ One Battery Attached

AC INPUT

Top View

BATTERY CHARGING 

STATUS LEGEND

9

Summary of Contents for Link 800W

















Reviews: