background image

6

SmartNode 10100A Series Quick Start Guide

5.1  Guidelines

Use 10 AWG (minimum) stranded ground wire.

Terminate equipment side of ground wire with a #10 ring terminal.

Do NOT

 daisy chain the ground between equipment. Use a ground bus bar, as 

shown in 

figure 4

.

Figure 4. 

Chassis ground connection

Do not over-tighten ground lug connections.

Keep the length of the ground wire as short as possible.

5.2  Grounding procedure

Do the following to connect to the SN10100A series gateway to ground:

   1.

Connect one end of a ground wire to the ground lug of the SN10100 series gate-
way. See 

figure 4

.

   2.

Connect the other end of the ground wire to a ground bar of the equipment rack.If 
the SN10100 series gateway is not installed in an equipment rack, then connect 
the ground wire to the main water entry pipe.

   3.

Verify that the resistance of the ground path is less than 0.5 ohms.

To avoid the risk of fire, electric shock, or personal injury do not apply 
power to the SN10100A before the equipment chassis ground has been 
installed.

WARNING

G

r

o

un

d Ba

r

15

14

13

12

10 11

8

9

3

2

0

7

6

5

4

1

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

15

14

13

12

10 11

8

9

3

2

0

7

6

5

4

1

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

15

14

13

12

10 11

8

9

3

2

0

7

6

5

4

1

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

Ea

r

th

G

r

o

un

d

Summary of Contents for SmartNode SN10100A Series













Reviews: