background image

SmartNode 10100A Series Quick Start Guide

5

Note

Ethernet ports (ETH 0/0 & 0/1), and SMS ports (SMS-0/0 & 0/1) are not used 
when connecting VoIP.

Figure 2. 

Connecting the VoIP ports

4.0  Connecting to the PSTN

A SN10100A with 8 RJ48C type ports enables the connection to T1/E1 lines.

Note

T1/E1 ports are activated by software license; the number of active ports 
depends on the licenses purchased.

   1.

Start with port 0, located at the top and leftmost position. Connect one cable 
between this port and the T1/E1 line.

   2.

Repeat step 1, using the next available port 

Figure 3. 

Port Interface to the PSTN

5.0  Grounding the Equipment Chassis

As a standard safety practice, the chassis of the SN10100A series gateway must be 
properly grounded to protect against any contact with an electrical fault condition. It is 
recommended that the chassis be connected to an earth ground. If the SN10100A 
series gateway is mounted in an equipment rack, then the ground cable must be con-
nected from the ground lug of the SN10100A series gateway ground to the ground bar 
of the equipment rack. If more than one SN10100A series gateway is installed in an 
equipment rack, each SN10100A series gateway must be grounded directly to the 
equipment rack ground bar.

VoIP Netwo

r

k 1

15

14

13

12

10 11

8

9

3

2

0

7

6

5

4

1

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

VoIP Netwo

r

k 2

15

14

13

12

10 11

8

9

3

2

0

7

6

5

4

1

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

16-Po

r

t I

n

te

r

face to the P

S

TN

Summary of Contents for SmartNode SN10100A Series













Reviews: