Patton CopperLink 2300 Quick Start Manual Download Page 16

16

CopperLink 2300 Quick Start Guide

E  EC Declaration of Conformity

Product Description:

 Long Range CopperLink Ethernet Extender

We certify that the apparatus identified above conforms to the requirements of Council Directive 1999/5/EC on 
the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equip-
ment and the mutual recognition of their conformity.

The signed Declaration of Conformity can be downloaded from 

www.patton.com/certifications/

.

F  Authorized European Representative

D R M Green
European Compliance Services Limited.
Greyfriars Court
Paradise Square
Oxford, OX1 1BE, UK

F.1  Copyright statement

Copyright © 2013, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no 
liability for errors that may appear in this document.

F.2  Trademarks statement

The term 

CopperLink

 is a trademark of Patton Electronics Company. All other trademarks presented in this 

document are the property of their respective owners.

F.3  Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the 

CopperLink User Manual

 

located online 

at

www.patton.com/manuals

.

The safety advises in the documentation accompanying the products shall be 
obeyed. The conformity to the above directive is indicated by the CE sign on 
the device.

In accordance with the requirements of council directive 2002/96/EC on 
Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-
life you separate this product from other waste and scrap and deliver to the 
WEEE collection system in your country for recycling.

Summary of Contents for CopperLink 2300

















Reviews: