background image

33

34

APPENDIX A

PATTON MODEL 2094

SPECIFICATIONS

Network Data Rate:

2.048 Mbps

Network Connector:

RJ-48C

Nominal Impedance:

120 ohm (75 ohm available when using

Patton Model 460 Balun)

DTE Interface:

V.35 (DCE Orientation) on Male M/34

Line Coding:

Selectable AMI or HDB3

Line Framing:

G.703 (Unframed) or G.704/G.732

(Framed)

CAS Multiframing:

Selectable On or Off

CRC-4 Multiframing:

Selectable On or Off

Clocking:

Internal, External, or Receive Recover

DTE Data Rates:

64, 128, 192, 256, 384, 512, 640, 768,

1024, 1280, 1536, 1600, 1920, 1984,

2048 kbps

Time Slot Rate:

64 kbps

DS0 Start Position:

Arbitrary

DS0 Mapping Position:

Contiguous or Arbitrary

Diagnostics:

V.54 Loopback; V.52 Patterns:  511,

2047, and QRSS

Indicators:

Power, Transmit Data, Receive Data,

Alarm, Loss of Sync, Test Mode, Error

Configuration:

8-Position DIP Switch and RS-232

Control Port

Power Supply:

100-240VAC, 50-60Hz, 0.4A

Humidity:

Up to 90% non-condensing

Temperature:

0 to 70

o

C

Dimensions:  

9.0 x 5.3 x 2.0 cm (3.5”L x 2.1”W x

0.78”H)

APPENDIX B

PATTON MODEL 2094

CABLE RECOMMENDATIONS

The Patton Model 2094  has been performance tested by Patton

technicians using twisted-pair cable with the following characteristics:

Wire Gauge

Capacitance

Resistance

19 AWG

83nf/mi or 15.72 pf/ft.

.0163 Ohms/ft.

22 AWG

83nf/mi or 15.72 pf/ft.

.0326 Ohms/ft.

24 AWG

83nf/mi or 15.72 pf/ft.

.05165 Ohms/ft.

To gain optimum performance from the Model 2094 , please keep

the following guidelines in mind:

• 

Always use twisted pair wire—this is not an option.

• Use twisted pair wire with a capacitance of 20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid AWG
numbers higher than 26)

• Use of twisted pair with a resistance greater than the above
specifications may cause a reduction in maximum distance obtain-
able.  Functionality should not be affected.

• Many environmental factors can affect the maximum distance
obtainable at a particular site.  Use the above data rate/distance
table as a 

general guideline only.

    Model 2703B Distance Table - Km (Miles)

Data Rate

Wire Gauge

(kbps)

.7mm (22)

.5mm (24)

2048

1.2 (.76)

1.5 (.95)

Summary of Contents for 2094





















Reviews: