background image

7. DTE Controlled Remote Digital Loop

Select Option 7 in the SOFTWARE CONFIGURATION Menu to

enable DTE control of the Remote Digital Loop Menu (See below).  The
Remote Digital Loop on the 1092RC can be controlled from  the DTE
interface by selecting Enable (Option 1).  To instruct the 1092RC to
ignore this request from the DTE interface, select Disable (Option 2).

3.2.5  MAIN MENU Option 5:  Select Hardware/Software Control

Select Option 5 from the MAIN MENU selects  whether the Model

1092RC will use the hardware switch settings or the software switch
settings for its active configuration.  If Options 1 or 2 are selected, the
1092RC will use the current hardware or software switch settings as the
active configuration.  After changing this setting select MAIN MENU
Option 8 to implement the changes.

3.2.6  MAIN MENU Option 6:  Display Modem Status

Select Option 6 from MAIN MENU to display the Modem Status

(below).  Press RETURN on the keyboard to update and redisplay the
screen.

16

3.3  CONFIGURING THE REAR INTERFACE CARD

The Model 1092RC Series has two interface card options:  the

Model 1000RCM12592 (DB-25/RJ-45) and the Model 1000RCM13492
(M/34/RJ-45).  Each of these options supports one DTE interface
connection and one 2-wire line connection.  Figure 4 below illustrates
the two different interface options for the Model 1092RC Series.

NOTE:

The 1092RC Series rear cards are specifically designed to

operate with the Model 1092RC function card and must not be
swapped with other Patton function cards.

Prior to installation, you will need to examine the rear card you

have selected and make sure it is properly configured for your
application.  Each rear card is configured by setting straps located on
the PC board.  To configure the rear cards, you must set the
configuration straps.  Figure 5 below shows the orientation of these
straps.  Each strap can either be on pegs 1 and 2, or on pegs 2 and 3.
Sections 3.3.1 and 3.3.2 describe the strap locations and possible
settings for each rear card. 

21

Figure 4.

Model 1092RC Series interface card options 

DB-25 F

M/34 F

1

2

3

1

2

3

1

2

3

Figure 5.

Orientation of Interface Card Straps

connected

open

RJ-45

RJ-45

Model

1000RCM12592

Model

1000RCM13492

Summary of Contents for 1092RC









































Reviews: