background image

8

GB

Important!

When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with due
care. Keep this manual in a safe place, so that the
information is available at all times. If you give the
equipment to any other person, give them these
operating instructions as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.

1. Safety regulations

The corresponding safety information can be found
in the enclosed booklet.

CAUTION!

Read all safety regulations and instructions.

Any errors made in following the safety regulations

and instructions may result in an electric shock, fire

and/or serious injury.

Keep all safety regulations and instructions in a

safe place for future use.

Operating instructions for right-angle
grinders

Proper use

The angle grinder is designed for the cutting and
rough grinding of metal and masonry using the
appropriate cutting disk or rough grinding disk.

The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.

Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

VOLTAGE

Before you use the machine for the first time, check
that the voltage marked on the rating plate is the
same as your mains voltage. Under no
circumstances is the mains voltage to differ from the

rated voltage by more than 10%.

SWITCH

To switch on, push the locking button forward (1) 
and press the switch button (2). 

REPLACING THE GRINDING WHEEL
Pull out the power plug.

Simple wheel change by spindle
lock: Press the spindle lock and
allow the grinding wheel to latch
in place.Open the flange nut with
the face spanner.
Change the grinding or cutting
wheel and tighten the flange nut
with the face spanner.

Important! Only ever press the spindle lock 
when the motor and grinding spindle are at a
standstill! You must keep the spindle lock
pressed while you change the wheel!

For grinding or cutting wheels up to approx. 3 mm
thick, screw on the flange nut with the flat side facing
the grinding or cutting wheel.

TEST RUN FOR NEW GRINDING WHEELS

Allow the right-angle grinder to run in idle for at least
1 minute with the grinding or cutting wheel fitted in
place. Vibrating wheels are to be replaced
immediately.

MOTOR

It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilation
holes clean at all times.

ADDITIONAL HANDLE (FIG. 1)

The angle grinder comes with a special additional
handle that can be adapted to the working position in
question.
To fix the additional handle in position, turn the lock
nut (1) all the way onto the additional handle. Then
screw the additional handle fully onto the angle
grinder. Now adjust the handle to the position
required and fix it in place with the lock nut (1).

Important!

The thread of the additional handle has

to be screwed as far as possible into the angle
grinder.

Anleitung E-WS 230-2350_SPK7:_  14.12.2007  11:44 Uhr  Seite 8

Summary of Contents for 44 720 20

























































Reviews: