background image

9

GB

Swivel handle (Fig. 2)

The handle can be swiveled a maximum 90° to the
left and right. To do so, press the locking plate (1)
and swivel the handle 90° to the left or right.

Important! When the locking plate (1) engages
correctly it makes an audible click.

CARBON BRUSHES

Carbon brushes that are burned, broken or shorter
than 5 mm are to be replaced by original
replacement brushes. Always replace the carbon
brushes in pairs.

GRINDING WHEELS

Never use a grinding or cutting wheel bigger than the
specified diameter.
Before using a grinding or cutting wheel, check its
rated speed. The wheel´s rated speed must be
higher than the idle speed of the right-angle grinder.

Use only grinding and cutting wheels that are
approved for a minimum speed of 6,000 rpm and a
peripheral speed of 80 m/sec.

OPERATING MODES

Rough grinding:

For the best rough grinding results, hold the grinding
wheel at an angle of between 30° and 40° to the
workpiece surface and guide back and forth over the
workpiece in steady movements.

Cutting:

When you use the right-angle grinder for cutting
purposes, avoid tilting it in the cutting plane. The
cutting wheel must have a clean cutting edge.
A diamond cutting wheel is best used to cut hard
stone.
It is prohibited to use the machine on asbestos
materials!

It is prohibited to use the machine on asbestos
materials!

 

Never use a cutting wheel for rough grinding.

TECHNICAL DATA

Nominal voltage:

230 V ~ 50 Hz

Power consumption:

2350 W

Idle speed:

6.000 rpm

Max. wheel diameter:

230 mm

Drive spindle thread:

M 14

Sound pressure level LPA:

94,8 dB(A)

Sound power level LWA:

107,8 dB(A)

Vibration a

hv

3,9 m/s

2

Weight

5,8 kg

Totally insulated

II / 

Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.

Cleaning, maintenance and ordering of
spare parts

Always pull out the mains power plug before starting
any cleaning work.

Cleaning

Keep all safety devices, air vents and the motor 
housing free of dirt and dust as far as possible. 
Wipe the equipment with a clean cloth or blow it 
with compressed air at low pressure.

We recommend that you clean the device 
immediately each time you have finished using it.

Clean the equipment regularly with a moist cloth 
and some soft soap. Do not use cleaning agents 
or solvents; these could attack the plastic parts of 
the equipment. Ensure that no water can seep 
into the device.

Carbon brushes

In case of excessive sparking, have the carbon 
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.

Anleitung E-WS 230-2350_SPK7:_  14.12.2007  11:44 Uhr  Seite 9

Summary of Contents for 44 720 20

























































Reviews: