background image

10

12

trouble shooting

problem

possible Cause

CorreCtiVe aCtion

Insufficient 

output, low 

discharge 

pressure

Clogged inlet filter.

Leaks in air lines, air valves, 

fittings, etc...

Clean or replace as necessary.

Replace worn components as 

necessary.

Drive belts slipping.

Tension V-belts.

Drain valve left open.

Close drain valve.

Defective pressure gauge.

Replace pressure gauge.

Leaking head gasket.

Replace head gasket.

Dirty or plugged inter cooler 

tubes.

Remove and clean inter cooler 

tubes.

Pressure switch adjusted too 

low, or defective.

Make necessary adjustments.

Worn or defective compressor 

valves.

Replace valves.

Worn piston, worn out rings.

Replace worn parts.

Restrictive check valve.

Clean check valve and replace 

if necessary.

Motor stalls 

or blows 

breaker

Faulty check valve.

Valves incorrectly installed

Replace check valve.

Install valves correctly.

Drive belts too tight.

Tension V-belts.

Defective pressure switch.

Replace switch.

Defective Motor.

Replace Motor.

(Consult licensed electrician).

Power being supplied by 

generator.

Consult licensed electrician

Water in 

crankcase 

oil gets dirty, 

rusty valves 

or cylinders

Cycle too short; compressor 

does not operate long enough 

to vaporize condensed mois-

ture during compression.

Allow for longer operating 

cycle.

System pressure leaking back 

through check valve when 

compressor is stopped.

Check and replace check 

valve if necessary.

Wrong oil being used.

Drain and replace with proper 

oil

Summary of Contents for PA-C5060

















Reviews: