Page
8
of 16 HPS 848 R.2
User section
A
A
L
L
A
A
R
R
M
M
M
M
E
E
M
M
O
O
R
R
Y
Y
If the central unit records one or more causes of alarm, they are signaled, when disarming and open
the driver door or press the anti hi-theft push-button through the LED. To verify the type of alarm,
check the number of flashings of the LED with the table below.
N° Flash of the LED
C
AUSE
1
Doors opening (triggered by CAN-BUS)
2
CDL unlocking by mech. key (triggered by CAN-BUS),
or power supply
missing form wireless siren (only for list ≥ 35).
3
Hood (Bonnet) opening (triggered CAN-BUS)
4
Trunk opening (triggered CAN-BUS)
5
Ignition key turn on (triggered CAN-BUS)
6
Shock sensor triggered
7
Additional sensor trigger at pin input n° 3 (PINK wire) (U.S. sensor,
microwave sensor)
8
Additional sensor trigger at pin input n° 4 (BLUE wire)
11
OEM alarm (triggered CAN-BUS)
12
Magnetic sensors HPA 975 triggered
13
Hood (Bonnet) detected by wireless siren (only for list ≥ 35)
15
Missing communication with wireless siren (only for list ≥ 35)
V
V
A
A
L
L
E
E
T
T
F
F
U
U
N
N
C
C
T
T
I
I
O
O
N
N
This function puts the alarm into the stand-by modality. This allows the car to be left at a service
centre without leaving the remote control. It is activated, when the alarm is disarmed.
Activation:
Compose, using the ignition key, the
unlocking
code (factory setting 1-2-3).
If the operation is successful, the LED on the dashboard will flash twice.
To remind that the Valet function is active the LED on the dashboard will flash twice at
any time one turns on the ignition key.
Deactivation:
Compose using the ignition key the
unlocking
code (factory setting 1-2-3). If the
operation is successful, the LED on the dashboard will flash 4 times and all the system
functions will be restored.
It’s possible to active this function also through the ant
i theft
push-button: EASY VALET function
E
E
A
A
S
S
Y
Y
V
V
A
A
L
L
E
E
T
T
F
F
U
U
N
N
C
C
T
T
I
I
O
O
N
N
Activation of the EASY VALET function:
•
Ignition Key ON, front doors closed and alarm disarmed, push the anti theft button for
about 10 seconds, the LED start to flash slowly.
•
Release the button before the LED stops to flash.
If the function is enabled
-> 1 blinkers flash
–
1 beep
–
1 LED flash
If the function is disabled
-> 2 blinkers flashes
–
2 beeps
–
2 LED flashes
Every time that the ignition key is turned ON, the LED flash 2 times slowly for about 40
seconds, to show that the function is ON.
P
P
R
R
E
E
-
-
V
V
A
A
L
L
E
E
T
T
F
F
U
U
N
N
C
C
T
T
I
I
O
O
N
N
This function permit to disable the
anti aggression and anti theft functions
(if set), keeping ON
all the other functions of the alarm.
Activation of the PRE-VALET function:
•
Ignition key ON, front doors opened and alarm disarmed, push the anti theft button for
about 10 seconds, the LED start to flash slowly.
•
Release the button before the LED stops to flash.
If the function is enabled
-> 1 blinkers flash
–
1 beep
–
1 LED flash
If the function is disabled
-> 2 blinkers flashes
–
2 beeps
–
2 LED flashes
