Paton StandardMIG-160 Data Sheet And Operating Manual Download Page 21 | Manualshive

Page: 21 / 37

background image

-21 -

PATON

StandardMIG

MMA/TIG/MIG/MAG

diameter of installed wire (Ф0.6...1.2m). This configuration may be not optimal,
but, under condition of correct work, even wire feeding (without jerks) and correct
connection, this ‘ feeding machine” combination shall be able to weld so
far. For better results, adjust the source voltage with buttons

1

and wire feeding

speed by pressing buttons

12

on the wire-feeding machine according to general

recommendations on semiautomatic welding. Remember that these parameters
are different for each specific application.

5.1 WELDING CYCLE – MIG/MAG-2T

See Clause 6.1 for sequence of changing the value of any function in the

current welding mode.

5.1.1 FUNCTION OF BUTTON ON A 2T TORCH

It is used in welding of short and medium length welds. The function is as follows:
when pressing the button on the torch, the control signal enters the control unit,
the function of pre-purging the welding zone with gas during the time [t.Pr] (the
gas valve is opened) is processed, then a signal is given to turn on the source and

t, s

t, s

t, s

«
...
19
20
21
22
23
...
»

Summary of Contents for StandardMIG-160






































Reviews:

No comments

Related manuals for StandardMIG-160

Brand: Oklahoma Sound Pages: 2

Brand: Oklahoma Sound Pages: 13

Brand: Dantel Pages: 42

Brand: Genie Pages: 202

Brand: Bose Pages: 44

Brand: Abus Pages: 2

ABIPLAS CUT 200 W/MT

Brand: Abicor Binzel Pages: 100

Brand: EAW Pages: 2

XC Filter Cartridge EV9613-09

Brand: Everpure Pages: 2

Brand: Bang & Olufsen Pages: 44

KPN235WEK-WELIK-DC

Brand: Ravaglioli Pages: 76

Brand: Miller Pages: 56

Brand: BHM Medical Pages: 29

Brand: Dynacord Pages: 6

Brand: Studiomaster Professional Pages: 12

Brand: Landscape Vibrations Pages: 8

HSS-L2S-000 Series

Brand: MAGNASPHERE Pages: 2

Brand: Aquasound Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands