54
Buzzer sound No.4 was measured from the total circumference of the Buzzer Unit at 1m
Buzzer Unit
：
40mA (
※
1)
LED Unit
：
40mA
100-240V AC (50/60Hz)
90-250V AC (50/60Hz)
Buzzer Unit
：
1.5W (
※
1)
LED Unit
：
1.5W
LED Unit
：
1.8W
Buzzer Unit
：
1.8W (
※
1)
at 25
℃：
25A/ Less than 2ms (Cold-start)
at 50
℃：
50A/ Less than 2ms (Cold-start)
0.44kg + (0.035kg)×Tiers + [0.035kg]
0.50kg + (0.06kg)×Tiers + [0.060kg]
0.32kg + (0.06kg)×Tiers + [0.060kg]
0.25kg + (0.035kg)×Tiers + [0.035kg]
(LED Unit) + [Buzzer Unit]
Typ.88dB
Typ.85dB
Buzzer Unit
：
250mA (
※
1)
LED Unit
：
45mA
LR
□
-
□
M2
□□□
W
none
LED Unit
：
none
Buzzer Unit
：
0.2W
Body Unit
：
0.2W
1500VAC applied for 1min Between live part and non-current carrying metallic part without breaking insulation
LR4
PJ
WJ
PJ
WJ
0.60kg + (0.06kg)×Tiers + [0.060kg]
0.54kg + (0.035kg)×Tiers + [0.035kg]
LJ
LJ
LR6
LR4
LR6
General Specifications
（
M2
）
Max.
Operating Voltage Range
Typ.
Signal Wire Current
Rated Voltage
（
Per Unit
）
Rated Power
Consumption
（
Per Unit
）
Inrush Current
Model
Power Supply Wire
Signal Wire
Max.
Typ.
Standby Power Consumption
Mounting Direction
Environmental Condition
Setting
Insulation Resistance
Outer Dimensions
Buzzer Sound/
Typical Frequency
Operating Ambient Temperature
Operating Ambient Humidity
Storage Ambient Temperature
Storage Ambient Humidity
Mounting Location
Protection Rating
Withstand Voltage
Flashing Rate
Mass
(Tolerance ±10%)
Environmental Condition
Sound Pressure Level
No.1
No.2
No.3
No.4
Rapid Intermittent Beep / 3378Hz
Continuous Beep Sound / 3378Hz
Rapid Hi-Lo / 2016Hz&3012Hz
Sweep Sound / 1000Hz-4032Hz
Refer to Section 3 “
Part Names and Outer Appearance”
Depending on DIP Switch Settings.
Refer to Section 6 “Buzzer Pattern Set-up”.
60±2 Flashes Per Minute
Upright
Upright
IP65(IEC 60529) / NEMA TYPE 4X,13
IP54(IEC 60529) / NEMA TYPE 4X,13
More than 1M
Ω
at 500VDC between live part and non-current carrying metallic part
-20
℃
〜
+50
℃
Less than 90% RH (No Condensation)
-30
℃
〜
+60
℃
Less than 90% RH (No Condensation)
Indoor Only
UL 508, CSA-C22.2 No. 14, EMC Directive (EN 61000-6-4, EN 61000-6-2)
RoHS Directive (EN 50581), FCC Part 15 Subpart B Class A
KC (KN 61000-6-4, KN 61000-6-2) (
※
2), Low Voltage Directive(IEC/EN60947-5-1,EN62471)(
※
2)
(
※
1) Environmental Condition: Buzzer sound No.2 (Continuous Beep Sound)
(
※
2) Except LJ Type
UL Recognized Component (File No.E215660)
Conformity Standards
Remarks
●
When a regulated power supply is not being used, select a fuse that meets class CC or more.
●
Use
a fuse holder
with UL standard certification. (Conformity requirements for UL Standard)
●
This product is designed for use on a flat surface for a
Type 1 Enclosure
.
(Conformity requirements for UL Standard)
●
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These restrictions are limited to cases where this equipment is operated in a business district, and it is designed to take the
relevant protective measures against electromagnetic noise hindrance.
●
This product must not be used in residential areas. (Conformity requirements for the CE Marking)
Sound Reduction approximately -10dB,
depending on DIP Switch settings.
Refer to Section 6 “Buzzer Pattern Set-up”
Due to the characteristics of the LED elements, a variation in difference of the color tone and brightness
of every product may occur.
LJ
ghv Vertriebs-GmbH
| Am Schammacher Feld 47 | 85567 Grafing | T 49 80 92 81 89 0 | [email protected] |
www.ghv.de
