background image

 

11 

ASSEMBLY INSTRUCTIONS INGROUND POST MODELS 

 

PH-45-IG-LP     (Liquid Propane), PH-50-IG-N     (Natural Gas)  
PH-45-IG-D-LP (Liquid Propane), PH-50-IG-D-N (Natural Gas)  
for permanent inground post mounting.  “D” indicates heater with direct light 
electronic ignition, no standing pilot.  (Requires switched 24 Volt power supply to 
heater.) 

 

   
 Step 1

 

 Determine a safe, level and stable location for the        

heater to be installed. 
Step 2 
Bury ground support pipe in ground so that 
approximately 6” is protruding above ground level.  
Ensure that support pipe is plum and securely 
supported in concrete. 
Step3

 

Remove the 3/8” x 1” bolt in the base of the heater 
head and set aside. (Figure 2  previous page 7). Secure 
heater head to flexible hose protruding from the top of 
the post.  Use two pipe wrenches to securely tighten.  
A suitably approved gas pipe sealant must be used for 
all gas connections.  Slide head assembly into post. 
Align the 3/8” hole in the post with the 3/8” threaded 
hole in the base of the heater head, and replace the 
3/8” x 1” bolt.  Secure tightly. 
Step 4 
Insert post into the ground support pipe and fasten 
with hardware provided.  Connect the gas supply to 
the nipple protruding from the lower side of the tube.  
The gas supply piping and electrical supply (if 
applicable) must be done in accordance with all local 
and applicable codes.  Only those licensed and 
qualified in the installation of gas-fired appliances 
should be engaged to install this appliance. 
Step 5 
Secure the reflector to the heater head with the             
hardware provided. 

 
D-Direct Lite:  If your heater has been supplied with a 24 Volt remote switching option, or 
direct light electronic ignition, connect your switched 24 V power supply to the spade 
connectors protruding from the bottom end of the post. Connect spade connectors at the top 
of the post to the marked connections on the heater head.  All supply wiring must be done in 
accordance will national, local and applicable codes.   Only those qualified and experienced 
in such wiring should be engaged for the installation of the electrical supply.

Gas  shutoff
by others

Underground
gas supply

Underground
pipe support

Ground level

Summary of Contents for PH series





















Reviews: