
-
PMS2000 System
-
7
Ref.
11/500-B
PMW60-B, PMW120-B, PMW240-B
Questo particolare rende di facile realizzazione l’impianto e,
nel caso in cui un altoparlante dovesse per qualche motivo
scollegarsi dalla linea, il resto dell’impianto proseguirebbe nel
suo regolare funzionamento. Le tensioni costanti disponibili in
uscita dall’ampli
fi
catore sono da
50
,
70
e
100 V
. Per il corretto
dimensionamento dell’impianto (scelta della tensione di linea
dell’apparecchio e selezione della potenza del diffusore) é possibile
individuare diverse procedure, di seguito riportate con esempi
numerici.
This fact makes the system easy to create and, if any of the
loudspeakers should be disconnected from the line for any reason,
the rest of the system would continue to function properly. The
constant voltages available as outputs from the ampli
fi
er are
50
,
70
and
100 V
. There are several possible procedures for sizing the
system correctly (by choosing the line voltage of the equipment
or by choosing the output power of the loudspeaker). Numerical
examples of these procedures are provided below.
Fig. 3.3.2.1
3.3.3
Calcolo del numero di diffusori
(tramite le potenze)
Si supponga di avere de
fi
nito sia l’ampli
fi
catore (cioé la sua potenza
di uscita) che il tipo di diffusore con relativa potenza assorbita. In
questo caso il massimo numero di diffusori collegabile sulla linea
é determinato dalla seguente formula:
Esempio: si utilizzino un ampli
fi
catore PMW240-B, in grado di
erogare una potenza pari a 240 watt, con plafoniere da 10 watt
nominali. Per sapere quanti diffusori sono collegabili alla linea di
uscita si calcola:
3.3.4
Calcolo del numero di diffusori
(tramite le impedenze)
Se il dato disponibile é l’impedenza del diffusore, il numero
massimo di diffusori collegabili ad una linea é:
dove l’impedenza nominale dell’ampli
fi
catore é ricavabile dalla
tabella 3.3.1.
Esempio: si utilizzino un ampli
fi
catore PMW240-B con diffusori
che presentano una impedenza nominale pari a 833 ohm
(corrispondenti ad una potenza di 12 watt su linea a 100 volt).
Dalla tabella 3.3.1 si trova che l’impedenza nominale della linea
di uscita a 100 volt è pari a 42 ohm.
Quindi:
3.3.3
Calculating the number of loudspeakers
(on the basis of the power output)
It is assumed that both the ampli
fi
er (that is to say its output
power) and the type of loudspeaker with the relevant absorbed
power have both been de
fi
ned. In this case the maximum number
of loudspeakers that can be connected to the line is determined
by means of the following formula:
Example: A PMW240-B ampli
fi
er capable of delivering an output
power equal to 240 watt is used, with ceiling
fi
xtures rated at 10
watt. To
fi
nd out how many loudspeakers can be connected to
the output line, calculate the following:
3.3.4
Calculating the number of loudspeakers
(on the basis of the impedance)
If the available datum is the impedance of the loudspeaker, the
maximum number of loudspeakers that can be connected to a
line is:
Where the rated impedance of the ampli
fi
er can be found in
Table 3.3.1.
Example: A PMW240-B ampli
fi
er with loudspeakers that have a
rated impedance of 833 ohm (corresponding to an output power
of 12 watt on a 100 volt line) is used. Based on table 3.3.1 it can
be seen that the rated output of the output line at 100 volt is
equal to 42 ohm.
Therefore:
numero diffusori =
potenza ampli
fi
catore
potenza diffusore
numero diffusori =
impedenza nominale diffusore
impedenza ampli
fi
catore
numero diffusori =
240 W
10 W
= 24
numero diffusori =
833
42
= 19
number of loudspeakers =
ampli
fi
er power
loudspeaker power
number of loudspeakers =
loudspeaker rated impedance
ampli
fi
er impedance
number of loudspeakers =
240 W
10 W
= 24
number of loudspeakers =
833
42
= 19
11-672_senza concatenamento.indd7 7
11-672_senza concatenamento.indd7 7
22/03/2010 14.57.08
22/03/2010 14.57.08