background image

7

Battery and Charging System

Charging Instructions

1.

Remove wall mount unit with the orange label from
the tool case and plug into a 120V  AC outlet. Set
orange charger on a stable surface and insert wall
mount unit’s plug into plug receptacle on the back of
the charger (see picture).  A green light indicates
power is on and charger circuit is ready.

2.

Remove the battery from tool or case and insert
terminals down into charger. The red light will come
on indicating that the battery is charging and the
green light will go out.

      If battery is completely discharged, the red light and
     the green light may alternate back and forth for up to
     20 minutes. This safety feature slowly recharges the
     battery until it is ready to accept the full charging
     current.  If the red and green lights continue to
     alternate after 20 minutes, replace the battery.

3.

After charging is complete, the red light will go out
and the green light will come on, indicating that the
battery is fully charged. The charger will keep the
battery at full charge until it is removed.

4.

Unplug the wall mount unit from the charger and
remove the wall mount unit from the 120V AC outlet.

CHARGING TIMES:

First charge (new battery)

      2 hours

Discharged Battery

5 minutes to 2 hours

CHARGING DON'TS:

1.

Do not charge battery outdoors or in temperatures
below 40

°

F (5

°

C).

2.

Do not allow metal objects to come in contact with
battery terminals.

3.

Do not puncture or attempt to open battery case or
cells.

4.

Do not store battery where it will be subjected to
temperatures above 120

°

F (49

°

C).

5.

Do not incinerate battery.

6.

Do not use a defective battery charger, one that
over-heats and/or smokes when plugged in.

7.

Do not immerse the battery in water.

PaslodeCharging System Accessories:

Battery Charger Kit - Part No. 900200
Wall Mount Transformer* - Part No. 900477
Battery Charger Base* - Part No. 900476
Automotive Adapter* - Part No. 900507

* Cannot use with previous (gray in color) charging system
  components.

THE PASLODE BATTERY CHARGING SYSTEM

NOTE

Battery and Charging System

The Paslode Cordless tools come with a recharge-
able battery and its own charging system. This
charging system is the only one that will work with
the Pasldoe batteries (either round or oval ).

  

The first

step in preparing a new tool for operation is to fully
charge the battery. New batteries are shipped
discharged and must be charged prior to first
use. 
 Batteries will take 5 minutes to 2 hours (time
will be dependant on the amount of discharge of the
battery) to recharge.

Important Charging Notes

Plug

Warning

CHEMICAL/EXPLOSION
HAZARD
Read ALL instructions be-
fore charging or using bat-
tery.  Failure to follow ALL
instructions may result in
fire, severe burns, or re-
lease of toxic materials.

REAR VIEW OF

CHARGER BASE

Plug Receptacle

Battery Disposal:
The Paslode batteries contain cadmium and must be
recycled or disposed of properly.  It  is illegal in some
areas to place a nickel-cadmium battery into the trash
or solid waste stream.  You may contact your local
recycling center for information on where to return the
spent battery or call 1-800-822-8837 for information on
Ni-Cd battery recycling in your area.

Wall Mount Unit

Charger Base

Summary of Contents for IM200 F18





















Reviews: