background image

2

Introduction and Warranty

TrimMaster 18™ Finish Nailer
Operating Manual

This manual is intended to acquaint you with the Paslode
Cordless 18 Finish Nailer. Unlike other power fastening
tools, the Cordless 18 Finish Nailer is powered by an
internal combustion linear motor. In simpler terms, your
Cordless 18 Finish  Nailer is powered by a motor similar to
the one that powers an automobile. The Cordless 18 Finish
Nailer ignites a fuel and air mixture to produce the energy to
drive the motor, which in turn drives the fastener. The
Cordless 18 Finish Nailer is totally self-contained. It carries
its own fuel supply and battery, along with a supply of
fasteners.

For ease of use, this manual is divided into sections (see
Contents). Each section of the manual is written with you,
the tool operator, in mind. We have left out many of the
technical terms so that you can easily understand how to get
the maximum performance from your Cordless 18 Finish
Nailer, and how to avoid damaging the tool or injuring
yourself. But, to accomplish this, we need you to do two
things:

1. READ THE MANUAL FROM COVER TO COVER
    BEFORE USING THE TOOL.

2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.

The Finish nailer should be handled like other power
fastening tools that you use. Like most tools, when used
improperly injury could result . If you are going to allow
others to use the Finish nailer, it is your responsibility to
make sure that they also read and comply with the
instructions in this manual before attempting to operate
the tool.

Should you have questions about the Finish nailer, or wish
to obtain additional copies of this manual, please contact
your Paslode

® 

representative. The space below is provided

so that you may record your representative's name,
address, and telephone number.

For the nearest Paslode representative call 1-800-
682-3428

Name

Address

City

State

     Zip

Telephone  Number

Cordless Warranty and Limitations

Paslode warranties that new Cordless power fastening tools,
parts and accessories will be free from defects in material and
workmanship for the period shown below, after the date of
delivery to the original user.

ONE-YEAR LIMITED WARRANTY

A one-year warranty will apply to all parts, except those listed
below as normal wearing parts, or parts which are specifically
covered by an extended warranty.

FIVE-YEAR EXTENDED LIMITED WARRANTY

A five-year warranty will apply to all molded nylon parts:

Cap and Grille

Handle Halves and Actuator

Trigger

90-DAY LIMITED WARRANTY

A 90-day warranty applies to the following parts, which are
considered normal wear parts:

Bumper

Driver Blades

O-Rings

WARRANTY STATEMENT

Paslode's sole liability hereunder will be to replace any part or accessory
which proves to be defective within the specific time period. Any replacement
part or accessory provided in accordance with this warranty will carry a
warranty for the balance of the period of warranty applicable to the part it
replaces. This warranty does not apply to part replacement required due
to normal wear.

This warranty is void on any tool which has been subjected to misuse,
abuse, accidental or intentional damage, use with fasteners, fuel, batteries,
or battery chargers not meeting Paslode specification, size, or quantity,
improperly maintained, repaired with other than genuine Paslode
replacement parts, damaged in transit or handling, or which, in Paslode's
opinion, has been altered or repaired in a way that affects or detracts from
the performance of the tool.

PASLODE MAKES NO WARRANTY, EXPRESSED OR IMPLIED,
RELATING TO MERCHANTABILITY, FITNESS, OR OTHERWISE,
EXCEPT AS STATED ABOVE, and Paslode's liability AS STATED ABOVE
AND AS ASSUMED ABOVE is in lieu of all other warranties arising out of,
or in connection with, the use and performance of the tool, except to the
extent other wise provided by applicable law. PASLODE SHALL IN NO
EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGES WHICH
MAY ARISE FROM LOSS OF ANTICIPATED PROFITS OR
PRODUCTION, SPOILAGE OF MATERIALS,, INCREASED COST OF
OPERATION, OR OTHERWISE.

Summary of Contents for IM200 F18





















Reviews: