background image

user manual

A

ttention

It is forbidden to use nets and other devices that can obstruct the end of the flue 

(including caps for gas boilers) and to use "T" (figure 8) or "H" (figure 9) shaped 

terminals or  open caps (figure 10).

In the event that the mouth of the 

existing flue is not perpendicular to the 

smoke outlet of the hearth, their 

connection must be made using the 

appropriate inclined fitting

(figure 7).

figura 6

f

igura 8

figura 9

figura 10

The exhaust system must be unique for each generator, no discharges in the flue 

shared with other devices are allowed (figure 6).

(

figura 7

If the smoke exhaust is inserted inside a pre-existing flue, this must be certified for solid 

fuels, be kept in optimal conditions and appropriately insulated.

An external flue pipe can only be used if it meets the following requirements:

Only insulated (double-walled) stainless steel pipes fixed to the wall should be used for the 

ductsat the end of the duct there must be an inspection to perform periodic checks and 

maintenance.The duct must be equipped with a windproof chimney and respect the 

distances from the ridgeof the building (figure 11).

11

Summary of Contents for Flora

















































Reviews: