Partner K 650/700 Active Workshop Manual Download

Page: 63 / 96

505 38 13-08

502 50 55-01

502 50 82-01

Crankshaft and crankcase

Mod. 950

Pull off the seal with an extractor.

Mod. 950

Dismantle all parts on the clutch side so
that the seal becomes accessible.

Screw in the seal extractor as far as it
goes in the seal, and pull off the seal.

Lubricate the shaft with a few drops of oil
and fit a new seal.

Fit the other parts in the reverse order to
dismantling.

Lubricate the shaft with a few drops of oil
and fit a new seal in place with the plate
cover turned outwards.

Press the seal in the crankcase with a
suitable drift until it is flush with the
crankcase.

Check that the hole in the crankshaft for
lubrication of the clutch bearing is not
blocked. If so, clean with compressed air.

Fit the other parts in the reverse order to
dismantling.

NOTE!

Remember the spacer sleeve between
the clutch drum and crankcase.

Vibration dampers

Mod. 650, 700

Remove the screws and separate the
grip from the attachment in the crankcase.

Remove the damper.

Assembly is conducted in reverse order
to dismantling.

Vibration dampers

Mod. 650, 700

Remove the two screws (A) and separate
the grip from the attachment in the
crankcase.

Remove the damper (B). It may have to
be rotated to aid removal.

Fit a new damper in the reverse order to
dismantling.

The vibration damper at the cylinder can
be dismantled for replacement after the
screws (A) and (B) have been dismantled.

Summary of Contents for K 650/700 Active

































































































Search results

Summary of Contents for K 650/700 Active

Reviews:

Related manuals for K 650/700 Active

Brands by name

Popular brands

Partner K 650/700 Active, Workshop Manual

Search results

Summary of Contents for K 650/700 Active

Reviews:

Related manuals for K 650/700 Active

Brands by name

Popular brands