manualshive.com logo in svg

ParTech ASLD 2200 Monitor, Instruction Manual

Share
Download
ParTech ASLD 2200 Monitor Instruction Manual Download Page 18

Spare Parts

The parts listed below are available for the ASLD 2200; it is advisable to contact your local 
distributor or Partech’s technical support team before purchasing these parts to ensure that the 
correct items are purchased.

Sensor

Part No 

Description

179120

Soli-Tech 20 Sensor, Range 0-1,500 for ASLD 2200

179140

Soli-Tech 20 Sensor, Range 0-10,000 for ASLD 2200

179160

Soli-Tech 20 Sensor, Range 0-30,000 for ASLD 2200

102201

IR100 Sensor for ASLD 2200

101901

IR40 Sensor for ASLD 2200

101601

IR15 Sensor for ASLD 2200

148121

IR8 Sensor for ASLD 2200

General

Part No 

Description

101170

Mounting Bracket for ASLD 2200

103370

Instruction Manual for ASLD 2200

Repair

Part No 

Description

101480

1A Anti Surge Fuse (20 mm) located in fuse holder

103040

5A Anti Surge Fuse (20 mm) located on main CCA

101660

Drive Belt ASLD 2200 Motor Assembly Version 1

154110

Transformer Sub-Assembly  for ASLD 2200

117150

Encoder Disc 1 Bladed for ASLD 2200

117160

Encoder Disc 2 Bladed for ASLD 2200

117170

Encoder Disc 4 Bladed for ASLD 2200

121950

Encoder Disc 6 Bladed for ASLD 2200

121960

Encoder Disc 8 Bladed for ASLD 2200

222326

ASLD2200 Motor Assembly Version 2

222341

Drive Belt ASLD2200 Motor Assembly Version 2

Spare Partrs 

Page 18

Summary of Contents for ASLD 2200 Monitor






















Reviews:

No comments

Brands by name

Popular brands

Load more brands