manualshive.com logo in svg

ParTech 228531, Instruction Manual

Share
Download
ParTech 228531 Instruction Manual Download Page 7

7

Press Menu on the 

keypad to display the 

main menu.

The monitor shows 

the date and time of 

the last sample. Press 

OK.

Select Measurement 

Config with the arrow 

keys. Press OK.

Use.the.arrow.keys.to.

adjust.the.value..Press.

OK.

Choose Sample 

Result and press OK.

The sample result 

screen displays sensor 

info. Press OK.

The monitor displays 

a.success.message..

Press OK.

Dissolved Oxygen Sensor - 100% Open Air Calibration

Select Measurement 

Config and press the 

OK key.

Choose DO 

Saturation and press 

OK.

Highlight.Calibrate 

and press OK.

The monitor displays 

sensor info. Press OK.

Calibrate.the.RDO.sensor.using.the.0%.saturation.method.described.below..See.the.

manual for the Partech 750w

2

.Monitor.to.get.more.information.about.calibration..

Suspended Solids Sensor

 - Sample 

Result 

Calibration

Use.Sample.Result.to.adjust.the.value.stored.earlier.with.the.Take.Sample.function..

You must know the value of the calibration solution based on a lab analysis.

Select 

Suspended 

Solids

 with the arrow 

keys. Press 

OK

.

Calibrate the sensor in 

air, but not in a drafty 

environment. Press 

OK 

to continue.

Wait for a saturation 

percentage of roughly 

90%. Then press OK.

228538IM-Iss12

Summary of Contents for 228531

























Reviews:

No comments

Brands by name

Popular brands

Load more brands