Parkside PWH 2800 B2, Operating And Safety Instructions, Translation Of Original Operating Manual

Page: 14 / 176

9 GB/IE
• With accessories as well as wearing parts and replace-
ment parts use only original parts. Replacement parts can
be obtained from your dealer.
• When ordering please provide our article number as well
as type and year of manufacture for your equipment.
• Before connecting the machine, make certain that the data
on the type plate matches with the mains power data.
m DANGER
The device and the packaging are
not children‘s toys! Do not let chil-
dren play with plastic bags, films
or small parts! There is a danger of
choking or suffocating!
9. Assembly
m WARNING!
Always pull out the mains plug before carry-
ing out adjustments on the device.
9.1 Fitting the support feet (Fig. 3/4)
1. Position the roller shredder so that the support feet (6) can
be folded out by 180°.
2. Guide the wheel axle (13) into the intended position on
the support feet (6). (Fig. 4)
9.2 Fitting the wheels (7) (fig. 5/6)
1. Assemble both wheels (7), as shown in fig. 6, using the
lock nuts (14), the wheel sleeves (15) and the wash-
ers (16). Use the tool supplied to tighten the wheels (7).
NOTE: If the axle rotates when tightening, use the Allen
key (b) to hold in place.
2. After tightening the locknut (14), fit the wheel cap (17) on
the wheel (7).
9.3 Installing the collecting container (Fig. 7, 8, 9)
1. Set the safety switch (9) on the collecting container (8) to
its lowest position (Fig. 7).
2. Slide the collecting container (8) along the guide rail into
the machine stand. The collecting container (8) can only
be pushed in one direction.
3. To lock the collecting container (8), push the safety switch
(9) on the collecting container (8) back up as far as it will
go (Fig. 8; 9).
9.4 Fitting the handle for the adjusting screw (5b)
(Fig. 10)
The adjusting screw (5) can be used to adjust the pressure
plate (23) inside the device. The exact setting of the pressure
plate (23) is explained under point 10.9.
1. Remove the pre-fitted fixing screw (5a).
2. Put the handle for the adjusting screw (5b) on the free end
of the adjusting screw (5).
3. Tighten the pre-fitted fixing screw (5a).
10. Operation
The roller shredder has a powerful electric motor, overload
protection and a restart lock for additional safety. A roller sys-
tem is used as the cutting system, which works very quietly and
automatically pulls in the chopped material. The robust chassis
provides stability and good mobility of the device.
Please refer to the following descriptions for the function of
the controls.
Attention!
The roller shredder can only be
started when the collecting con-
tainer (8) is pushed into the ma-
chine stand and the safety switch
(9) is in the top position.
10.1 Connecting the extension cable (Fig. 11)
1. Form a loop from the end of the extension cable and hook
it into the strain relief (20) on the mains cable (10).
2. Connect the extension cable.
10.1.1 Status LED (18) (Fig . 2)
The status LED (18) shows you whether your device is con-
nected to the power supply.
If the status LED (18) lights up, your device is supplied with
power and can start up.
10.2 Switching on and off (Fig. 2)
1. On switch (2): The roller shredder is started when this but-
ton is pressed.
2. Off switch (3): The roller shredder is stopped when this
button is pressed.
10.3 Switch for direction of roller rotation (11)
(Fig. 2)
• Switch position “I” Entry:
- By pressing this button, the device runs in continuous op-
eration. Material is drawn in.
• Switch position “0” Stop:
- Device stops.
• Switch position “II” Reverse:
- You can change the direction of rotation of the cutting
roller (Reverse) to remove jammed chopped material. Set
the switch for the roller rotation direction to “II”. As soon
as you press and hold the on switch (2) (jog mode), the
device runs in reverse. Trapped chopped material is re-
leased.
10.4 Overload switch (12)
The motor is equipped with an overload switch (12). If the
roller shredder is overloaded, the overload switch switches off
automatically to protect the roller shredder from overheating.
1. If the overload switch has triggered, switch the roller
shredder off at the off switch (3) and wait until the roller
shredder has cooled down.
2. Now press the overload switch (12) and switch the roller
shredder on again.